oh ? i never did enabled it. i tried with the same settings as you Native but didn't work.
Did you make any other changes to the setup to enable it ?


Edit - ok got it post #143 and swap from ethernet to ppp done.

This post has been edited by jeisern: Jul 19 2016, 11:22 PM

Yes, native.
Interface is PPP.

Others no need change but if you want to use Google DNS, then disable Connect to DNS Server automatically, input them in IPv6 DNS server 1 and server 2.

This post has been edited by fruitie: Jul 19 2016, 11:18 PM

ohhhh u replied too fast, i was browsing through the threads !

thanks neways....i got it up. new to this custom firmware thing.... ok let's see how i overkill my 100mbps connection.

This post has been edited by jeisern: Jul 19 2016, 11:24 PM

You are welcome.

For now, not much benefits for me, so I just disabled it.

Mine the details will show up in the system log -> ipv6 tab ... but when I try to do those online ipv6 tests it will always fail.

My test always shows 8/10 but still working.

Sricom still got restock this router ?

This asuswrt able to do isolate lan vlan with ip pool?
Eg : lan1: 192.168.1.x
lan2: 192.168.2.x
lan3: 192.168.3.x

Bandwidth limiter able to set each ip get ul 2m/dl 2m ?

Thanks.

The router scan more reliable. Thats the source point for your network ma.


It was stock clearance so i doubt got restock.

No obvious vlan options. Guest networks available which isolates subnets.

Bandwidth limiting available but haven;t test.

Successful flash to xwrt. But i don know where the multi ssid and vlan setting hiding. Damn.

Ask a noob question. After flashing xwrt vortex just key in unifi id and password only? Do i need to do factory reset 1st before proceed? Any particular need to fill up like vlan for iptv and voip?

Yeah for me i just key in the unifi id and password
For the IPTV by default its LAN 4
I did not make any changes to the VOIP so i can't help you.

To get an overview you can check via the administration tab
The column on the left basically allows you to go through the options.
Not really that complicated gui

Thanks. Will try when i home. Unif too jew for me coz just start using 2days. Still using unifi DIR850L now. Will try to set up ws880 Asuswrt again. Last nite took me an hour but still just can connect to internet but my wifi just got 2.4g. Can't find the factory reset option to proceed. It is under administration tab?

Better to do factory reset to be safe, dunno what's left on your NVRAM.

'Multi SSID' don't have, they call it 'guest network', can have up to 3 additional each for 2.4/5GHz.

VLAN really don't see it anywhere, if you want to play with that go for Tomato.

Can directly flash to Tomato? How? I really wan to wireless connect to my Hypptv.

Guys,

Appreciate some help here. I managed to get this router at the very attractive price, thanks to you guys over here. I managed to successfully flash the router to ASUS-XWRT firmware, but somehow i couldn't get it to connect to unifi.

I'm very sure my unifi password is correct, as i just installed new unifi 30mpbs, and i've snapped a picture of the password given by the installer. When I plug into TM's default router, it will connect in less than 15 seconds or so. But when i plugged into WS880, it wont connect.

I've key in correct user ID and password for sure. After that when detecting connection type, it always say time off.
I can see the WLAN and WPS light on WS880, with WLAN blinking (indicating wireless user connected) and WPS light permanent on. I cannot see the INTERNET light. I've done a soft and hard reset, but still couldn't connect to unifi.

Any ideas? Could be the new firmware, somehow i miss the steps or the firmware is corrupted? Can i reflash it again using the same method?

Same way you flashed to Vortex, but no need the CFE as you have already done that. I think Vortex management page also gives you an option to flash.

If you want to confirm your unifi password is correct, go re-setup TM default router using that password. Most likely password problem. Or easier way, call 100, give them your details, and they'll give you the right password. It may be that you thought 0 is o or something.

Alternatively it could be your router defective. Haven't heard of such a case in this thread yet though. Try the password first.

Hi, Thanks for your prompt reply. Already did as per your suggestion, reset the router password, and re-key in again. TM router is able to connect to unifi.

any other suggestions? hmmm..

have you tick the "special requirement for isp" box below the password column.

ahh... okok. now i can get it online. Need to tick the"special requirement for IPS" box and select Unifi-Home option.

thanks alot bro!

The special requirement has to be selected as that will tell the router to do the necessary VLAN tagging for UniFi.