QUOTE(kimsim @ Jul 22 2015, 09:38 PM)
so cheap. 3M aircon filter rm 18 already. which one better?Aircon Discussion V3, Home Appliance
Aircon Discussion V3, Home Appliance
|
|
Jul 23 2015, 08:30 AM
|
![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
1,686 posts Joined: May 2012 |
|
|
|
|
|
|
Jul 23 2015, 08:32 AM
|
![]() ![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
5,847 posts Joined: Nov 2010 From: Malaysia 🇲🇾 |
|
|
|
Jul 23 2015, 08:38 AM
|
![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
1,686 posts Joined: May 2012 |
|
|
|
Jul 23 2015, 08:41 AM
|
![]() ![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
5,847 posts Joined: Nov 2010 From: Malaysia 🇲🇾 |
|
|
|
Jul 26 2015, 01:16 AM
|
![]() ![]() ![]() ![]() ![]()
Senior Member
891 posts Joined: Nov 2006 |
This contractor quote me price for inverter aircon with conceal and back-to-back, do u guys think is it reasonable? Conceal part all are less than 10 feets
Conceal: 1)To coceal 1.0h/p inverter a/cond copper piping and drain pipe.-RM500(Grd flr bed room) 2)To coceal 1.5h/p inverter a/cond copper piping and drain pipe.-RM680(Living Hall) 3)1.5h/p PANASONIC wall split unit a/cond.-RM430(Master bedroom) 4)To install 1set 1.5h/p PANASONIC inverter wall split unit a/cond.-RM150(Living Hall) Back-to-back 1)To install 2sets 1.0h/p PANASONIC inverter wall split unit a/cond.-RM380×2sets=RM760(1st flr 2bedroom) |
|
|
Jul 26 2015, 07:58 AM
|
![]()
Junior Member
26 posts Joined: May 2012 |
QUOTE(kimsim @ Jul 12 2015, 11:13 PM) Fujitsu inverter good also, but the drain pan can't be remove also difficult to clean on fan blower by normal service. I want to find out if Pana cooling coil can be dismantle for outdoor cleaning. I managed to removed the blower fan for high pressure jet cleaning, super clean now.![]() It is difficult to diy clean cooling coil, I use enzime fluid + steam cleaner, but I think using high pressure water jet cleaning is the best if possible. Do you know if sharp's blower and cooling coil can be removed? Thanks |
|
|
|
|
|
Jul 26 2015, 08:51 AM
|
![]() ![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
5,847 posts Joined: Nov 2010 From: Malaysia 🇲🇾 |
QUOTE(esoo88 @ Jul 26 2015, 07:58 AM) I want to find out if Pana cooling coil can be dismantle for outdoor cleaning. I managed to removed the blower fan for high pressure jet cleaning, super clean now. Outdoor unit just use jet water spray was good enough, for indoor need to dismantle but the flare nuts must be know how to fixed it back without gas leaking as well.It is difficult to diy clean cooling coil, I use enzime fluid + steam cleaner, but I think using high pressure water jet cleaning is the best if possible. Do you know if sharp's blower and cooling coil can be removed? Thanks Again my indoor cooling coil also use water slowly spray by my own too. Before ![]() After cleaned, not 100% but still look for minor dust stick on, better than nothing ![]() My jet spray here ![]() Also remember to cover on electronic portion ![]() |
|
|
Jul 26 2015, 11:56 AM
|
![]()
Junior Member
26 posts Joined: May 2012 |
QUOTE(kimsim @ Jul 26 2015, 08:51 AM) Outdoor unit just use jet water spray was good enough, for indoor need to dismantle but the flare nuts must be know how to fixed it back without gas leaking as well. Do you use chemical to wash? How do you managet the waste water when u rinse with water? Use plastic bag? Again my indoor cooling coil also use water slowly spray by my own too. Before ![]() After cleaned, not 100% but still look for minor dust stick on, better than nothing ![]() My jet spray here ![]() Also remember to cover on electronic portion ![]() |
|
|
Jul 26 2015, 02:41 PM
|
![]() ![]()
Junior Member
81 posts Joined: Apr 2014 From: Bora-Bora Island |
Anyone have tried the new York? The one made fully by Johnson Controls
Links: http://www.yorkmy.com/york_malaysia.html http://www.11street.my/productdetail/new-y...ysl3f10-1163660 |
|
|
Jul 27 2015, 07:48 AM
|
![]() ![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
5,847 posts Joined: Nov 2010 From: Malaysia 🇲🇾 |
QUOTE(leonhart88 @ Jul 23 2015, 08:38 AM) MHI internal looks Wow the products design of internal wiring feel like made in China one. Fan blower can remove, but don't simple remove it, after the fan motor portion lose and can't fixed back as well. The additional feature like left & right horizontal swing is good for lazy person, from Pana deluxe also have same feature ![]() PCB portion ![]() ![]() Cooling coin still ok, better than Pana design ![]() The look before remove drain pan ![]() ![]() This post has been edited by kimsim: Jul 27 2015, 07:51 AM |
|
|
Jul 27 2015, 08:03 AM
|
![]() ![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
5,847 posts Joined: Nov 2010 From: Malaysia 🇲🇾 |
QUOTE(esoo88 @ Jul 26 2015, 11:56 AM) Do you use chemical to wash? How do you managet the waste water when u rinse with water? Use plastic bag? No never do a chemical wash before even for all Aircons, the condition of 6 yrs now.Use water spray may take some time lah. Slowly spraying, for water will overfall from drain pan, but make sure carry something can be holding water lah. My floors get wet also, after done n mop it only. |
|
|
Jul 27 2015, 10:42 AM
|
![]() ![]() ![]() ![]()
Senior Member
684 posts Joined: Dec 2007 |
want to ask horrr..
currently got 2 inverter aircon in apartment one is working well which the compress just place behind the wall of the wall using the accurate pipe however, my room's actually gt aircond come from the developer, not inverter model, the normal pipe already plant inside the wall which the wall also stand as tiang (developer advice not to touch so much on wall, will crack)... so due to complicated procedure... i just let the aircon man install the inverter aircon using the current pipe. yet the aircond is a little bit far from the compressor place.. the aircond man said will make the aircond take longer time to cool.. but after i move in and use...feel the aircond not so cold.. every night need to turn on until 20, just got cool feel... while the other aircond no need... anybody can advice on it? shud i call another aircond man to have a look on it? or... the situation is like tat ... cannot change//./ |
|
|
Jul 27 2015, 10:46 AM
|
![]() ![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
5,847 posts Joined: Nov 2010 From: Malaysia 🇲🇾 |
QUOTE(rae0724 @ Jul 27 2015, 10:42 AM) want to ask horrr.. currently got 2 inverter aircon in apartment one is working well which the compress just place behind the wall of the wall using the accurate pipe however, my room's actually gt aircond come from the developer, not inverter model, the normal pipe already plant inside the wall which the wall also stand as tiang (developer advice not to touch so much on wall, will crack)... so due to complicated procedure... i just let the aircon man install the inverter aircon using the current pipe. yet the aircond is a little bit far from the compressor place.. the aircond man said will make the aircond take longer time to cool.. but after i move in and use...feel the aircond not so cold.. every night need to turn on until 20, just got cool feel... while the other aircond no need... anybody can advice on it? shud i call another aircond man to have a look on it? or... the situation is like tat ... cannot change//./ Try to engage another Aircon man and refil new gas would be more sufficient lah. Mostly longer than 3-4m long should check the gas pressure. Like SG all use multi split and the piping longer than 5-7m then how? The gas pressure should more importantly at all |
|
|
|
|
|
Jul 28 2015, 10:30 AM
|
![]() ![]() ![]() ![]()
Senior Member
684 posts Joined: Dec 2007 |
QUOTE(kimsim @ Jul 27 2015, 10:46 AM) Try to engage another Aircon man and refil new gas would be more sufficient lah. i seeMostly longer than 3-4m long should check the gas pressure. Like SG all use multi split and the piping longer than 5-7m then how? The gas pressure should more importantly at all coz before the aircond finish install.. the aircond man oso gt refill gas inside.. (this gas not same with the gas pressure?) lowyat's aircond man here good or not? |
|
|
Jul 29 2015, 08:24 AM
|
![]() ![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
5,847 posts Joined: Nov 2010 From: Malaysia 🇲🇾 |
QUOTE(rae0724 @ Jul 28 2015, 10:30 AM) i see Pre-gas for enought between back to back an installed only, once an over 3m long should check the gas pressure wether is enough or not.coz before the aircond finish install.. the aircond man oso gt refill gas inside.. (this gas not same with the gas pressure?) lowyat's aircond man here good or not? Gas for Aircon is the most important one. Once low gas or shortage for the unit won't get cold at all, even set for 20-16C |
|
|
Jul 29 2015, 08:39 AM
|
![]() ![]()
Junior Member
57 posts Joined: May 2015 |
Hi All. is the Samsung inverter ac model AR09JVFSB better than others inverter brand?planning to buy this model n need some advice from sifu here.thanks
|
|
|
Jul 29 2015, 08:42 AM
|
![]() ![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
5,847 posts Joined: Nov 2010 From: Malaysia 🇲🇾 |
|
|
|
Jul 29 2015, 09:57 AM
|
![]() ![]()
Junior Member
57 posts Joined: May 2015 |
|
|
|
Jul 29 2015, 11:31 AM
|
![]() ![]() ![]() ![]() ![]()
Senior Member
891 posts Joined: Nov 2006 |
|
|
|
Jul 29 2015, 11:55 AM
|
![]() ![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
5,847 posts Joined: Nov 2010 From: Malaysia 🇲🇾 |
|
| Change to: | 0.0202sec
0.42
6 queries
GZIP Disabled
Time is now: 26th November 2025 - 12:44 PM |