same as me too.around that temp . but i find it out ... cause my fan running at 8xx rpm


This post has been edited by meons: Jun 23 2013, 11:17 AM

I just check on him.....he says he got a 4670K Costa Rica 330 batch (?) and the rest of hardware waiting from NCIX.
So,I beleive is not from same place (anyway no pic at all).



Dino told me a couple of weeks (last week).
Owi,what your brother in USA says?

This post has been edited by stasio: Jun 23 2013, 12:19 PM

My elder bro is no longer working for Intel USA but just changed his job to a German company and left for EU this morning.

Today I am playing with Samsung based kit. Some crazy overvoltings lol.

2800 9-12-12-21-1T @ 2.275v on air

Nice one......much better read,write,copy in Aida....as subtiming is lower.
Only you didn't show single stick how far can go....12/13-31-31-45......

hai ...sawadee kap newbies here...wan learning about ocing proc serious very noob

1st i try with stock volt.. oli got max 42 multiplier before fail to boot under

then try up more volt 1.2 .. set up 43 multiplier and do some testing on it

here some ss
dunno is ok or not.. did i do wrong with it ram temp... dunno where it come from




using cm212 single fan
value ram hynix

This post has been edited by meons: Jun 23 2013, 01:55 PM

Something wrong..... your LinX time is much longer and your Gflops is low. Are you running windows 7 sp1?

Take a look at mine:



Time of 71 (seconds?) and 114 GFlops.

gave up trying doing 1n. moving on

yes win7 64bit sp1

how to fix it?

This post has been edited by meons: Jun 23 2013, 02:12 PM

Set cpu voltage mode to manual
set ring voltage mode to manual

Set cpu voltage mode to manual
then set ure voltage
set ring voltage mode to manual
u can leave it at auto or set it = to ure vcore. up ure cache multi to 100-300mhz less than ure cpu.

is it me or it seems 4670k batches are worse than 4770k. hardly found any on the net worth mentioning.

just get the latest version of IBT. its already updated and will work.

This post has been edited by cstkl1: Jun 23 2013, 02:46 PM

oh like i mentioned, i use Small FFT settings. Prime95 stresses the processor adequately.

yes, downloaded from 1st post.

I'm using Windows 8 though.

Oopsss! I'm also new to Haswell.

Try IBT as suggested by cstkl1.

Not too sure about windows 8. Here's my prime95 using small FFTs for non-sp1 (no AVX) and sp1 (with AVX)

Non-SP1


SP1


Both are running default small FFTs but note the difference in the screen, type-0 FFTs vs AVX FFTs...... Your is AVX FFTs?

That time we spent too much time on that ES chip, which was total disappointment, around 7.30p.m we changed Kelvin's 4770k into the rig and only started tweaking all the way to 9.30pm nia
And we also need to let the staff inside Swisspac to go back mah, so, cabut lor~~~

This one, approximately RM2500 I guess.

Costa Rica batch #3307B197, as per Owi notes.........first publicly posted.




This post has been edited by stasio: Jun 23 2013, 06:07 PM

donno. i see temps going beyond 80c, so i didn't continue with it.

thank broo.... i will try again

it my mistake too .. i should build i7 rig ... but wan save some money and build as i5 rig
saving some money to grab gtx780 ...

mybe need sell it off ..and build i7 rig

This post has been edited by meons: Jun 23 2013, 10:07 PM

no prob ... even me more n0ob

i will take note..what you all post... mybe i can use it... give some try

Nice one. So he wasn't cheating.
I guess Costa 4770K is also around the corner.
Can't wait to grab some of them.

Yea,I asked him to show the pic..
Btw,my last Costa (IB),I also get from San Jose,California.