Sifus,why my rooter, 12am disconnect.need restart manually

Using latest hm red...

have you try to reboot the router again ?

how long the connection is going before it disconnected ?

did you enable the keep connection alive function under modem tab -> connection ?

Quite long...only 12am disconnect.. Noticed it today as I recall last note also same time

Already enabled that setting..

So sad, bro rebooted many times, reset the device n reentry the setting.but same same so i tought if use original firmware can work right?

did you run any CMD command prompt ping -t command in your computer/ connected device to the rooter ?

i did normally run CMD ping 8.8.8.8 -t in my computer,.. then guess the firewall in rooter take that as SYN-flood attack, LOL,.

so i disable that option under network -> firewall -> untick the syn-flood protection -> save and apply

and finally my rooter is no longer Disconnected everytime after running 18~24hour anymore,.

This post has been edited by chuahcs79: Nov 16 2013, 01:10 AM

so far i know that only certain batch E3276 can work with the original stock firmware,..
for futher detail on that. i guess u better contact your modem seller for futher confirm information

my E3276 cannot work at all with all the stock firmware including the latest beta version mr3420v2_en_3_13_30_up_boot(130314)Beta.bin

This post has been edited by chuahcs79: Nov 16 2013, 01:08 AM

Those who get E3276 can't work properly with Rooter please include your firmware version.

P/S : e3276 with firmware lower than 160 is likely to have problem with Routers.
Do not attempt to update firmware.

Will post some tutorial tomorrow.

This post has been edited by blacktubi: Nov 16 2013, 01:27 AM

thansk bro...mine i think could be the e3276 firmware, until today duno how to check the huawei firmware

i know my mr3420 is using the latest huntsman red firmware, should work...but my huawei one, how to check and flash it? thanks black tubi

Tools > Diagnostics
Use Mobile Partner

I prefer yellow, red seem a bit buggy. Personal preference.

i prefer red, the yellow rooter dont work well with my E3276 though

Yellow maybe good for V1 hardware, V2 hardware use Red

Bro,try black widow..as I'm having same problem with you previously.after installed blackwidow, I can connect in less than 2 minutes..

Can check my posts few pages back..

Then only I flash back hm..dunno whether its can work with your modem or not

Try n error

gastacopz, i will try that in a while

blacktubi, my e3276 firmware is 21.132.01.00.000 / software ver. 23.006.02.01.03

which one should i update?

fuelsave : I already mentioned do not update E3276 firmware for every E3276 running firmware older than 160.

Edit : Can anyone upload the OpenWRT 10-12 image for MR3420 V2.

My MR3420 V1 running 10-12 working perfectly well while both of the latest image for V2 don't work

This post has been edited by blacktubi: Nov 16 2013, 12:38 PM

I'm running 10-16 red with MR3420v2, modem can detect but can't dial
use that AT command result ERROR.

Here is the huntsman for TL-MR3420 V2 :

it contain huntsman from 2013-06-03 until now,. the whole huntsman packages

This post has been edited by chuahcs79: Nov 16 2013, 05:33 PM

i am using the latest red version of huntman 2013-11-10red

my e3276 firmware is 21.132.01.00.000 / software ver. 23.006.02.01.03 as well

so far it is working fine now,

This post has been edited by chuahcs79: Nov 16 2013, 05:36 PM

hmm look like same version of firmware.


currently I'm running BlackWidow2013-04-13 works well without AT command.

This post has been edited by lpc26: Nov 16 2013, 05:39 PM

oh ? so do you face any disconnected sometime ? will the blackwidow 2013-04-13 able to reconnect ?