how do i flash back to factory firmware from Huntsman?

do 30/30/30 reset or is there any specific methods to re-flash from custom firmware back to factory firmware?

Hi guys,
Do you guys try celcom m30??? I heard from my supplier that can reach 5 to 10mbps. But at my area there only can reach 3mbps in handphone. I am living at kuching, sarawak.

The most importance thing is when I plug it in O2 7.2mbps usb modern and plug to TL-MR3420 router..... only can runt for few minutes with 2mbps speed.... after that will drop to 0.08kbps......

Anyone got use celcom m30 plan please tell me how to do the setting....

Anyway, what is openwrt? for what? Will it be better?

Thanks.

Hmm just flashed to rooter latest firmware, no go,

Ive tried countless of time changing the data port and communication port, the page above also no info
increase or decrease whatever port also same, E3331 probably too new
I got E3276 but not sure if wanna convert it to normal modem

Can I configure like this

SIM->Huawei E398->TP-Link MR3420->Cisco EA4500 ? Will the performance degrade?

In this case, must as well just get the cheaper MR3020 and route to a better wireless router??

Bro, where to remove IPV6? 

Get an error when enter this command...
E398 U1V2... anything wrong? 

AT^FREQLOCK=1,54F4

Cell ID :  54F4(21748)

i using mr3020 with stock firmware with e398 (LTE Network)

connect direct pc get 35Mbps, on MR3020 (latest stock firmware) 32Mbps speed

Ping increase only by 2ms (wifi)

i would say MR3020 is not as bad as ppl describe it to be. As long as you upgrade to the latest firmware.

Mr3020 on ROOter is much better , try that 

You selling MR3020 for rm60 ?

I nak satu

her steps is wrong or wat? I dont want brick my router
tat one got one major problem. The usb port is 1.1 standard not 2.0 like mr3020

^ Same, wifi doesn't seem to be that good =/

Btw I bought a v2.2, flashed it to openwrt-ar71xx-generic-tl-mr3420-v2-squashfs-factory, managed to configure it to get my e398 up and running. then changed the ssid and tested the wifi, everything was working fine until that point.

then i unplugged my ethernet cable, put it back to my old router, then plugged back to mr3420 again and all the settings were gone, kept showing "no password is configured yet". after that i tried changing the WAN and wifi settings but it just won't save even after clicking save & apply/rebooting. at this point i can't change any of the settings, anyone encountered this before?

This one:

https://app.box.com/s/cqk23ztqlux1zs034896/...08/5685099156/1

wait till 2000 post, i take over, okay

Ok I flashed back to stock, then flashed to black widow.

Everything worked fine after the first configuration, but after reboot the WAN settings were gone(back to DHCP). Configured the WAN settings again and clicked save and apply but screen got stuck at saving/configuring etc/host/dhcp and now I can't even ping the router IP. Restarted and still get stuck when I try to configure WAN.

Anyone encountered this before? Not sure if it's a hardware issue or because I'm using a v2.2 model that's not compatible with v2 firmware.

anyone use 3420v1 with the latest stock firmware?
how's the duration from switch on (power up) to online (finish connecting 3G modem).
is it slow (a few minutes) like last time?

Anyone face modem automatic unplug, disconnection on tplink mr3420, mr3040?

trying to do port forwarding but still cannot work.

Details:
Gameranger UDP 16000

have done the setting on virtual servers

16000 with IP 192.168.0.100

BUT
got error message
"Port-Restricted Cone NAT Router"

keep saying need to set to
"This should be set to 192.168.0.100"

On stock version.
anyone can help ar?

Huawei E392u-12

You got latest E392u-12 firmware?
Current firmware =  Maxis Original firmware 

by the way, you got E5776?