any link to how to do that ar?

Got any side effect after applying public ip?

but i am using Celcom prepaid sim wor

My modem is original from maxis (lock), i had done with dc-unlocker (paid unlock).
Can i still your firmware?

How leh? 

after firmware update, i notice that the speed increase
on DC-HSPA+

I am trying to connect Sierra Wireless 753S to Huntsman 2013-07-21 running on TL-WR1043ND but I am getting this message below from kernel log and can't get an Internet connection: -

[  308.410000] usb 1-1: USB disconnect, device number 2
[  308.410000] sierra ttyUSB0: Sierra USB modem converter now disconnected from ttyUSB0
[  308.420000] sierra 1-1:1.0: device disconnected
[  308.430000] sierra ttyUSB1: Sierra USB modem converter now disconnected from ttyUSB1
[  308.440000] sierra 1-1:1.1: device disconnected
[  308.440000] sierra ttyUSB2: Sierra USB modem converter now disconnected from ttyUSB2
[  308.450000] sierra 1-1:1.2: device disconnected
[  308.450000] sierra ttyUSB3: Sierra USB modem converter now disconnected from ttyUSB3
[  308.460000] sierra 1-1:1.3: device disconnected
[  308.490000] sierra_net 1-1:1.7 wwan0: unregister 'sierra_net' usb-ehci-platform-1, Sierra Wireless USB-to-WWAN Modem
[  308.520000] sierra_net 1-1:1.7 (unregistered net_device): usb_control_msg failed, status -19
[  329.730000] usb 1-1: new high-speed USB device number 3 using ehci-platform
[  329.880000] usb 1-1: config 1 has an invalid interface number: 9 but max is 5
[  329.880000] usb 1-1: config 1 has an invalid interface number: 7 but max is 5
[  329.890000] usb 1-1: config 1 has no interface number 4
[  329.900000] usb 1-1: config 1 has no interface number 5

Ok, direct IP method is it USB tethering? If yes, then need install additional...will try again

http://wiki.openwrt.org/doc/howto/usb.tethering

What do u mean by 760S method? 

How to configure the router to connect to the internet faster than waiting for a few minutes?
I think I saw a post explaining the steps back ago but can't seem to find it now..

I am using Openwrt Rooter

I flashed from black widow to original firmware using SSH. After writing the firmware and rebooting, I can't load the router using my browser anymore.

Telnet/SSH doesn't work because it's original firmware.
I tried factory reset, clear ARP, using wireless to connect, all doesn't work.
Can ping the router IP (192.168.0.1 for v2.2) with response, but when i access using browser it just shows "TP-MR3420" as header while showing that it's loading...but it never loads.

Anyone encountered this before?

Seems to be my only option for now, just worried that I can't claim warranty if they suspect I've flashed it to openwrt, or they won't allow 1:1 exchange since it's slightly over a week =/

This MR3420 vs MR3020, which one is better in terms of reliability (turning on for 24 x 7) without restarting...

1st Day 3G/4G WARNING Ping DNS failed, timeout interval 60 seconds
1st Day 3G/4G 00:32:28 WARNING Detect DNS and NTP failed in this?

Having this error in my stock firmware tp-link mr3420 often and i cant connect to internet although the modem show connected and the light on the modem or broadband all fine..

any pro of sifu got any idea how to solve this problem? thanks

i have flash mr 3420 v2 with openwrt.

all step have done. now my wireless still not work

0% SSID: 1517 | Mode: Unknown

or in SSH

wlan0    ESSID: unknown
          Access Point: 00:00:00:00:00:00
          Mode: Client  Channel: 11 (2.462 GHz)
          Tx-Power: 18 dBm  Link Quality: 0/70
          Signal: unknown  Noise: -80 dBm
          Bit Rate: unknown
          Encryption: WPA2 PSK (CCMP)
          Type: nl80211  HW Mode(s): 802.11bgn
          Hardware: unknown [Generic MAC80211]
          TX power offset: unknown
          Frequency offset: unknown
          Supports VAPs: no

Why each time the router rebooted, it will ask for the SIM pin? I thought it will save it permanently?

I am using TP-Link TL-WR1043ND v1.10 with Huntsman 2013-07-21. Could it be firmware at Sierra Wireless 753S? Thanks.

ttyUSB2 doesn't work but ttyUSB3 works as below: -



the WWAN0 of 1043ND doesn't get any IP assigned from AC753S USB.

should I stop/disconnect the dial at AC753S?

I place the modem outside my house. Literally like outside.

The signal strength still showing 0%

[attachmentid=3670677]

checked, still the version 12.09