the auto power saving features are from intel chips.

World Record=5805mhz

Hi I got a problem.

I got a new E8400 (replacing E6320) using Gigabyte P35-DS3 (1.0) but nothing comes out! What gives?

Did you reset the bios?

If so, did you update your bios to the latest version?

Just a warning note.... some Gigabyte P35-DS3 version 1.0 have some problems with BIOS updates.... It is reported in many forums... you might just end up with a dead mobo like I did, had to RMA but they gave me version 2.0 .....

This post has been edited by kmarc: Jun 11 2008, 11:11 PM

Have not done any update yet. I can recall seeing my BIOS as an "F2" version. Is that version support to work with the e8400?

No way to update the bios without CPU?

Alamak! F2 is very the old leh.... now already F13i for the Ga-P35-DS3.... See here : http://www.gigabyte.com.tw/Support/Motherb...?ProductID=2544

Cannot kua..... I've never heard of updating a bios of a normal/average mobo without a CPU....

But even with the F2 bios is it significant enough to cause the entire system unit to not able to function at all? No display but got power.

Update: After updating the bios to F13i everything working fine!

This post has been edited by pirateguy: Jun 12 2008, 12:19 PM

Not too sure about that....... however, an F2 bios is quite an old bios.... even my 1 year old P35-DS3 was an F3....

Any advice how to overclock a 2.8ghz prescott proc? Noob here.. my mobo can't seem to change these voltage/fsb settings

I want to ask:

I bought a Q9300 (should have bought Q6600 >_>)

FSB now is 1500, why can't I go further?

mobo refuse boot, need clear cmos.

My friend advice me to increase Vcore, but I forgot what's the value I should increase for both NB and Vcore >.<

RAM value RAM >_> only can reach 1000MHz

cant change means cannot overclock..

---

Added on June 12, 2008, 5:55 pmQ9300 limited multiplier... there is a fsb limit on the proc maybe u hitted it... what fsb and multiplier are u running at? and while overclocking increasing voltage is a must if u wanna go higher..

This post has been edited by IcEMoCHa: Jun 12 2008, 05:55 PM

i guess its easier if u show us some cpu-z.....

run ur ram to 1:1...

maximum advised vcore for peryn is below 1.4v.....

for quad core, u'll need to tweak ur Vtt or Vfsb as well...

Yaya >.<

I dunno how.

Someone showed me the appropriate value to set in Overclocking.

then I tested with 1000MHz FSB on RAM, and it works!

but after I set to 1600MHz FSB for my 9300, the mobo died and everything was reseted.

So now I'm running on 1500MHz for Proc, Stock (800MHz) for RAM

I'm using a C2D E6850 at 3.0ghz. But i'm also using the DP35DP as my motherboard. Is there any way to overclock my processor? I heard that there's no way to overclock Intel mobos

Use setfsb but max is about 370FSB

Oh? That won't give me very much of an increase right? Rather pointless then?

Hi all sifu sifu sekalian,


I'm having some problem on overclocking my proc using my board. (E8400 with P5N32E-SLi).

1st attempt unable to POST. With below settings

FSB Memory clock mode - unlinked
FSB (QDR) MHz - 1600
FSB Memory ratio - Auto
FSB Memory - 800
Vcore volt - 1.25
Memory volt -1.85
1.2HT volt - 1.2
NB volt - 1.2
SB volt - 1.5
CPU VTT volt - 1.2

2nd attempt able to POST but hung at POST. With below settings

FSB Memory clock mode - unlinked
FSB (QDR) MHz - 1600
FSB Memory ratio - Auto
FSB Memory - 800
Vcore volt - 1.25
Memory volt -1.85
1.2HT volt - 1.35
NB volt - 1.35
SB volt - 1.5
CPU VTT volt - 1.35


Trying on 3.6 GHz. These thing is driving me crazy. HELP ME!!!! TQ

look at the E8 thread... there are many here..

Damn if u got problem how am I gonna upgrade to E8 series later?!...

sorry, my question will go a bit off topic because i dun wan to open a new thread
my fren is using pentium 4 socket 775, 2x 1gb ddr2 800mhz, gigabyte ep-35 ds3, and zotac 9600GT amp!

apparently there are a few weird things on his pc

1st. His ram is running at 533 only, cpu is running at 3.0ghz with 133x23(which i think the 23 is locked)noob me, his proc is 533 fsb, thats why
2nd. his gc, core speed detected correctly, but memory speed only detected as 1750(using rivatuner, gpu-z couldn't start, no idea why)
3rd. no software can detect the accurate temperature for processor, was using speedfan but not sure how accurate is it(realtemp and coretemp not supported, everest not even showing cpu temp)


hope buddies here can help me

This post has been edited by darude87: Jun 15 2008, 01:36 AM