So sorry.......do you want me to change the format now or have you gotten the data?

zt_lee : ASUS P4C800 E Deluxe

RAM = 2 X 512 Twinmos Value RAM
Chipset = Mtec AA4T [Winbond UTT CH-5]
Vdimm Applied = 3.3V
1T or 2T = 1T
System = AMD Athlon XP @ 2380 mhz



This post has been edited by Hyde`fK: Jul 15 2005, 02:18 AM

dinster, please update my result

RAM = 1x 512MB TwinMOS Speed Premium PC3200
Chipset = Winbond UTT CH-5
VDIMM = 3.2V
CPC = ON (1T)
System = AMD Sempron 3000+ (S-754) @ 2.56GHz

This post has been edited by soulfly: Jun 10 2005, 05:57 PM


Attached thumbnail(s)

@ soulfly

your utt ch5 bought from powerslide,right? should be can run at 2-2-2-5.

@ almostthere

so lucky to get 0351 MPMW gem

This post has been edited by gsan: Jun 10 2005, 07:38 PM

didnt notice this thread...will post mine afterwards...still burning. nice going din for starting the thread...

can. but limited to 250mhz with only 3.2Vdimm

with 2-3-2-x, it allows me to go further without hurting the bandwidth so much.

OCZ Clears Up the TCC5 Confusion

http://www.ocztechnology.com/aboutocz/news/31

it would be nice if u can post again using the template given + Sandra screenie + CPU-Z memory screenie (since ur info is not complete)

updated again...

RAM = 2x256mb Corsair XMS PC3500
chipset = Winbond BH5
Vdimm applied = 3.63v
1T or 2T = 1T
system = Athlon XP-M
CPU speed = 2516 Mhz

updated again...

RAM = 2x256mb Corsair XMS PC3500
chipset = Winbond BH5
Vdimm applied = 3.63v
1T or 2T = 1T
system = Athlon XP-M
CPU speed = 2516 Mhz



This post has been edited by gsan: Jun 11 2005, 08:30 PM

i jz have a look at lowyat today. It is a TWINX1024-3200 with latency 3-3-3-8! But actually i am not really know what the latency 3338 used for:-( Willing to learn..thanks:-) It should be this model:-

http://www.corsairmemory.com/corsair/xms.html#twinx

Plz comments...or should i get OCZ VALUE VX? Or even get a better performance ram 256X2 instead of 512X2?Thanks again:-)

This post has been edited by yeefung: Jun 12 2005, 01:25 AM


Attached thumbnail(s)

u have to check the revision number.. i think the ones u saw are not C2.. the C2 runs at 2.5-3-3-7 rated for amd systems and 2-3-3-7 for intel..

what board will u be looking at buying?

2x256 BH-5 performs better than 2x512mb simple because they are single sided.. it allows better overclockability..

if u can get the value vx.. get them.. they are good stuff

@ babyelf

for old generation of bh5, normally how far the double sided can be overclocked ?

just got myself a new toy... still in burning in process...
the ram less than 24hours old...
currently burn in at 205mhz 2-2-2-5@3V...
TMSP DDR PC3500 X2 512MB new BH-5.
The ram just got out of the box n didnt even run at
stock timing hehehe...

at most double-sided bh5/6 can go up to at least 250 at 3.5V if ur lucky... some get lesser than that

@ rzonealley

how much you bought the ram? btw, 1A4T need 3.0v to run 2-2-2-5 lo?

i have to agreed that for old generation of BH-5. but for newer BH-5 the overclockability
is unpredictable even on 2x512mb.

actually based on what i read 1A4T can run at 200mhz 2-2-2-5 at 2.9v
since the ram very new not even a day i intended to run at higher voltage at low mhz.
got the ram from robyncom for RM670.
this is the 6hours the ram running memtest without any error.

@ rzonealley

i see i see... then we're waiting for your further result ya

gsan.. my 2x512mb bh-5 will go to 270 with 3.5-3.6v

i played CSS at those speeds as well for about 30min before i get error.. so yea.. at those speeds i can bench i'm sure.. i think i can go higher.. but haven't tried it..

single sided usually goes up to 270-280 with about 3.6v for good pairs..

jslut.. 3.5v 250 is really really bad for old bh-5 already..

rzonealley.. yea new modules are hard to say.. i still prefer older modules.. my bh-5 never failed me my value vx in the other hand is not bad as well.. altho it didn't go as high as my bh-5

This post has been edited by babyelf: Jun 12 2005, 10:22 AM