i've hotflashed my bios. but then can't do it with original bios. it only accepts mantarays...aih

y sad...mantarays is the best oc bios...
even vcore can go til 2.05v still can boot

but then one thing i cant understand is, i cant flash back to original bios. that's y i flash to mantarays.

1t or 2t?
y tis the ood bios for L12 mod...
u can get high fsb then other bios... (my mobo lah)
max i get is 265++ 270 can boot n login winxp but 4-5 min mouse start hang...then keyboard...but the pc still on...winamp still playing mp3...tat the funny thing

i oso dunno wat happen...

anyone face tis problem? mind to share?

one of the reason i like this bios is the L12 mod. someone suggested me to use 1T. not sure wat's the difference.

can i know wat ram did u use??

here my 265 cpuz

that's nothing with the bios, psu is the main reason. before i'm using enlight 350w, once i set vcore to 2.0v, the pc must automatic shutdown. but since change to acbel 450w, i can get more than that.

yes, i faced it before. this problem occure due to the either SB or NB overheating. before adding the heatsink on SB, once the fsb over 248, my mouse n keyboard will hang but the mp3 still playing. but since adding heatsink on SB, this problem can overcome.

1T give more bandwidth score whereas 2T give more fsb since it's come with some loosing setting.

2xKHX256 2700

Command Rate CMD (1/ 2) (Command Rate, MA 1T/2T Select)
Number of clock cycles needed to address the memory module and the memory chip with the desired data zone. If your memory banks (slots) are full to capacity, you will have to raise this rate to two, resulting in a considerable drop in performance.

http://www.obm.co.nz/obmnew/guides/ddrram.htm

DRAM command rate specifies the time to wait after a chip select before activate and read can be started. It is usually suggested that you apply the lowest command rate that your RAM and motherboard can run stable with. The lesser the value, the quicker the memory controller be able to send commands out. On the other hand, at higher frequencies it might be crucial to raise the command rate latency in order to get your system at super stable state.

btw..just wanna ask...i thought L12 mod is for Tbred models only where the default FSB is @ 133? barton can use this mod also? FYI im using a unlocked desktop barton....

- ABIT-NF7D27-3DFire-1T
- ABIT-NF7D27-3DFire-2T

Which is better for my system ?

AXP-M 2400
2*512mb KVR

No hotwire mod ( L12 )

Main thing is that i only use FSB @ 200
Not trying to max things out
Enough juice for me at the moment

This post has been edited by ivandj: Aug 9 2005, 08:21 AM

if your ram is doubleSided,,, then go for 2T

How to flash the bios ?
just use Abit's flashmenu ?

just try to use it ,,, you're find it yourself,,, no worry easy only.

Well, i would sugested that you using D26 MantarayXT 2T or D27 Taipan 2T...
and EDc18R1 and B4r1 from Trats... with 2T of course...
And flashed using FlashMenu 2.91... I heard the new one have problem with Bandwith Memory...

D26 MantarayXT 2T or D27 Taipan 2T

Where can i get those?
Currently im running on Abit latest bios.
So can i still change my bios to those 2?

wow! bcoz of bios can burn mobo also.

Want to ask sifu here, which bios is good for CH-5 ram for NF7v2 board???

Also for CH-5 how high the FSB that it can reach? I'm using 2-3-2-11 timing, is there any other timing better than this?

This post has been edited by HiT-AbLe: Aug 12 2005, 12:23 AM

Do the 3.3v vdimm mod on ur nf7 and away you go with your overclocking. If I'm not mistaken, try going for Trats bios. It worked well for me

Correct me if I'm wrong.

This post has been edited by colinwong89: Aug 12 2005, 12:37 PM

yeah... trats bios rock