This problem happen only when i use windows OS. When I use Ubuntu live CD, my pc can Shutdown normally. I tried formatted my windows also not work.

To those on overclocked Brisbane G2 core at 3Ghz and above... how much is your vcore?
I am having trouble getting higher than 245 x 12.5 ( 3062 Mhz), currently set at 1.4V only.

Here is my screenie


This post has been edited by sharpman: Nov 12 2008, 10:41 PM

Nice Vcore there . I need at least 1.3xV to get Orthos stable with my previous x2 4600+ Brisbane ..

1 think 1.4xV to get Orthos stable at 3.1Ghz .
Brisby is Vcore hungry

Thanks.. how about the RAM, since I do not overclock the RAM it should be left at 1.8V ?
1st timer here

no need to increase the vdimm...since u dont o'c it

U r clocking the proc using HTT ..sure ur ram also been clock

I have set my RAM clock to 667Mhz (/8 divider) . Rrom my limited understanding my DDR2-800 ram is now underclocked at 766Mhz. Or there are other things that suggest my ram has been overclocked?

bro..ur ram default/stock speed is 667/800? coz from ur screenshot i saw 382 means 764..so as bro digswell said setting HTT will affect ur ram speed too..vdimm it depends on what type of ram u r using..

This post has been edited by FuiLo: Nov 12 2008, 11:39 PM

default is 800

Sry bro..juz saw ur post above..since u set ur divider to 667..i guess 1.8v is enough as 764 is still below the default 800

So u divider it to 667 ..... and run 766mhz dont mean u no oc ur ram
but if run below 800mhz can use default stock vdimm

yep..agree

10 seems to be my highest whole number multi that i can select but i seem to be very unstable anywhere above 300x10, even though i have booted into O/S at 3.25ghz but not sure if ram timings, CPU/chipset voltages or htlink multi are holding me back? at the moment i am at 1500mhz htlink - but this is very stable unlike my old board which anything over 1000mhz would just bsod.
have tried using 1.47v vcore but doesnt like it much, do u think that it could be a missed timing on the rams side of things or just needs another bump in vcore to get it to where it needs to be?

thanks for your help mate,

-updated my clock-









have anyone stress using LINX how it goes more stressing than orthos or prime?

updated again now @ 3300mhz paste on page 9 tq

This post has been edited by sepulgilo: Nov 14 2008, 12:13 PM

Thanks for the heads up

bro how bout u post up some screenie
easier for people to help u...btw as i told u b4
if u woried bout rams limiting u back,
dun o'c the ram first...loosen the timing and use the lowest divider possible
try to see how high cn ur proc goes...try bump up the vcore until
u find dat sweet max point for it...and btw 1.47 oredi kinda high
make sure u got sufficient cooling

hiya mate, thanks again for your help.

heres a screen dump of my rig:


ram is running @ 2.3v,
cpu idle 19* - 26* load 27* - 38* max


This post has been edited by blackenthesoul: Nov 13 2008, 07:13 PM

Sepulgilo, i've been noticing a few times alredy but are u running ur gpu at half of it pcie speed?
I see it's running at 8x speed instead of 16x, are u running CF?

i also want to attach my oc....

maybe this night...

owh hahaha i didnt notice that at all hehee later i chk the setting again

i did move my card from master to slave to master maybe it has activate the xfire mode

will reinstall driver and should be ok ehehheeehee

thanks for reminding me


peh still show 8x heehhe after read the manual again seems i have to slot in the paddle card so it will run 16x hehehe later la do that

This post has been edited by sepulgilo: Nov 13 2008, 10:08 AM