ya.. 100 warnings.. =.="

anyway, it is advisible to OC using easytune 6 or clock it at BIOS?

i dun use easytune6.
its better for OCing in bios then in windows.

i oni use easytune 6 to check hw far can it goes,and check the current voltage input.after evrthg is tested stable,i set it in the bios

w00t! just got my megahalems

megahalems can fit ep45-ud3p?what casing u using btw?

im using ud3r.. same thing right..

casing HAF932

---

Added on June 2, 2009, 4:25 pmtemps so far

http://img144.imageshack.us/img144/5704/temps.gif

This post has been edited by lightonokira: Jun 2 2009, 04:25 PM

ya ud3p and ud3r are same in terms of design and layout.but my casing is cm690,wonder wheter it will fit

This post has been edited by ZeneticX: Jun 2 2009, 04:26 PM

not sure bout that..

since this is my first aftermarket heatsink xD

---

Added on June 2, 2009, 4:29 pmis the temp normal?

This post has been edited by lightonokira: Jun 2 2009, 04:29 PM

try stressing it with a better program like LinX or IBT

after stress is 52°C?? before this when u use stock HSF, how much is it? if not mistaken is around 62~65°C??

---

Added on June 2, 2009, 4:41 pmoh ya, the LLC in bios got wat use.. it says what decrease Vdroop? should i enable it when i OC or onli enable it when i change Vcore?

This post has been edited by farscope: Jun 2 2009, 04:41 PM

LLC is load line calibration. decrease vdroop.
usually i turn it on so its easier for me to "bajet" the vcore.

ya.. i noe it stands for load line calibration.. my question is.. we enable it when we need to change voltage rite? or else juz off it?

where to get LinX?

here can get

the error ILLEGAL SUMOUT came after i increase 5mhz FSB..after that i reduce 5mhz FSB again and run Small FFts for 5 mins and everything is fine
i run Prime95 for 1 hour..in that time i increase my FSB by 5mhz for each 5 minutes to test my max clock i can go without vc0re adjusted

100 warnings in my Prime95?? is it the error:illegal sumout??im pretty new to this software
i suggest u OC at BIOS..let say u want OC your processor @3.5ghz <---set this in your bios.
If u want OC higher .Your target is @4ghz.Use Easytune6 to increase your FSB for overclocking..(try increase the FSB by 5mhz for each 5 minutes..if no errors in prime95,continue)
Once u get errors,reduce fsb by 5mhz. So this is your OC limit.
if u want higher(of couse) u must adjust the vcore, but i nvr try this ..

that's just my 2 cents.
if u dont understand..can try ask from other pro OC-er

pump vnb to 1.2v and c...wat ram u using?

Kingston Perfomance RAM PC2-6400(400mhz) 5-5-5-18 adjusted to 5-5-5-18
i just downclock my ram following the guide i read..huhu

u need to stress prime95 for almost 1 day to really test for full stability.thts why i prefer LinX or IBT more

can giv a brief method of using LinX? what "problem size" and "memory to use should" i put? or juz use default?

how many loops i need to put?

i prefer linx rather than prime95..

just run 30 loops is enuf 4 me. it consume around 30min only