I manage to get my Q9450 @ 3.2ghz, not sure about my vcore, cos cant seem to set it on my DFI P35 Bloodiron. My vcore doesnt seems to increase when i set my VTT higher.

According to CPUZ, my vcore jumps to and from 1.16 - 1.20.

nope..
just open rig setup..
so better airflow..

how much VTT you set?

oic... but i still get 73'c max without my side panel on... ish ish

what TIM you used bro?maybe using Tuniq TX2 will help a bit...

im using CM Nanofusion... reviews says that its as good as AS5
havent try TX2 yet... maybe after i get my venomous lah

CM Nanofusion is ok..but i don't like it because it's hard to apply to proc...hehehehhe...

yeah... its very hard to apply and because of that, i always need to apply alot so that there would be no gaps or empty space between...

AS5 and Tuniq TX2
TX2 win ?

from what i read on online reveiws, AS5 > nanofusion
but if malaysia review says that Tuniq TX2 is better than AS5 means

TX2 > AS5 > Nanofusion ???

1.100v. What is VTT by the way?

i not quite sure bro...for me Tuniq TX2 is ok for me...because it's more cheaper & good performance too...Nanofusion i tried once but i dont like it because hard to applied to proc...for AS5 never try it yet

---

Added on March 23, 2010, 8:03 pmiinm VTT is voltage termination for processor...and i read (forgot which thread)..if we setting VTT too high will damage your proc..not your vcore...correct me if i'm wrong...


This post has been edited by nidzamputra: Mar 23 2010, 08:03 PM

HEllo out there..i tried to change the frequency in BIOS..somehow its like a darkened space , i cant change it..it was a 333x8.5...q9550 here..using stock cooler...will it be a problem if i set it to 3ghz? hehe

arrrggghhhh one of my mushkin pair have problem..need to RMA ...now running 2gb only... ...and i feel the different

@kahjye
better you take the bios picture & show to us..maybe we can help you...think running 3ghz with stock HSF no problem...it's still can handle

hi all,

running my Q9550 on biostar G31 board @ 3.2Ghz (stock vcore) now, seems to be hitting the FSB wall already @ 386Mhz.. system just wont boot at all 387Mhz even after upping vcore, and im going no where..

anyone letting go any good clockable mATX LGA775 mobo?

hai
i nbe here. can't any one help me to oc my cpu?

i try to oc but went i open cpuz nothing change.
plz help me..

Irony: I just swapped my tracers for mushkins. They tracers weren't the D9G chips though...

How much do you guys think I can squeeze out from a CCF cooler for 24/7 usage? I managed to go up to 3.8GHz with my proc prime stable but the temps were

HI.. i'm noob here.. Just entered overclock in last 5 days...
I am using CORE 2 QUAD Q9650 3.0 , ASUS P5P43TD PRO, TEAM XTREEM DARK DDR3 1600 2X2GB...
Although i'm new here i could manage OCed to 3.6Ghz stable in 3 hours prime95 without any errors all 4 cores.. this is my setting in BIOS AI TWEAKER..
CPU Ratio Setting: 9.0
FSB Frequency:400
DRAM Frequency: 1333
PCIE Frequency:100
CPU Voltage:1.268
Others is AUTO
Temperature idle:50c
Temperature Load:60c
Cooled by: Cooler Master TX3 2 fans

My questions:
1. Is it Normal my temperature? since my brother using same proc & Heatsink @ 3.6GHZ in P5K PRO his temp only 46c in idle and 54 in load
2. Is it good setting since many setting in my AI Tweaker is Auto?
3. How i can OCed to 4.0Ghz (444x9.0)? Since i googled so many times searching how to set up it, most of them using P45 mobo such as P5Q deluxe and Maximus II Formula.. trying using those setting, but FAILED as ALWAYS... My system just can not enter the bios (blank screen) when i setting it at those setting..your help will be appreciated.



This post has been edited by krule91: Nov 27 2011, 04:23 PM

1.)That is not an accurate way to check temperature.
Try to download Core Temp for accurate temperature reading
2.)To verify if your oc is stable,try to use Intel Burn Test(Run 5 loops,3000MB)
If it pass than OC +/- stable enough.
3.)445x9 you have to trial and error yourself.
Start by getting 445x6 stable first(Set your VTT,VNB correct first) than change it to x9 and adjust vcore accordingly
Got any question can PM me
Besides i can do oc service for a fee as well

thanks for replying me for FOC hehe ... anyway.. forgot to say i'm using pc probe to read the temperature..
for number 3, i will try first test an error.

Is it a wise choice to downgrade motherboard from P45 to P43 just to run cheaper rams which is DDR3.

yeah.. my previous mobo Gigabyte 945p-ds3 does not support fsb 1333.. i ended buying p43 chipset which support ddr3 because cheaper ram. rather than buying p45.