Hi Sifu..

I cant find proper stand fan thread.. can i ask here? is there any good looking stand fan and wall fan with strong wind? haha....

recently just bought Pana econavi fan for living.. but parents refuse to use ceiling in bedroom due to Feng Shui.... 

would like to ask if anyone is using Rezo fan?

Hows the fan now? Still quiet working well?

Is rezo brand ok sifus?

my panasonic ceiling fan had noises after I clean the blades, maybe due to blades not balanced? anyway to DIY because my warranty period is over.. if called technician, how much does it cost?

I am unable to purchase any KDK any fans in JB. absolutely no stock. 

Also, one vendor mentioned that KDK fans are either made in Malaysia or Japan, the one made in Japan has a 5 year warranty with an almost double price tag.

is that true?

😳 which is the so called expensive models? Their Wi-Fi Nodoka is it made in Malaysia or Japan?

To be honest I'm confused on which brand to buy. All brands has bad reviews especially on motor, vibration and low speed after 1-2 years. Confused 😅

i use rezo at my current place, AX42 and S306. only used slightly over 1 year, no issues so far except the remote sometimes kinda shit.

I went looking for KDK z-series for my soon to be new place but its practically non existent in most shops now, so i opted back for rezo AX42 and Zetta 56.

Just as u said, you can find bad review on almost all fans, including the almighty KDK and Panasonic. It really depends on your luck sometimes.

I settled with Rezo still cause at least they have 5 yrs warranty while KDK only has 1 yr.

The only brand i will never touch is DEKA cause their bad reviews far outweigh any good reviews on them.

Hi, I bought a set of three Alpha brand ceiling fans recently, model AX666-5B. It works fine but one issue I have is that it makes some noise after it comes to a complete stop. Sometimes quite some time after it stops. It's a kind of rattling sound. It doesn't seem to affect the functioning and there is absolutely no sound when it is spinning. But it's unsettling.

Any idea what the problem could be?

Was looking for sensa 4 and all no stock even in shoppe and lazada

I asked this for my car porch too, the shop told me just use a cheap one will do... macam no proper answer only 

Hello, does anyone know where I can buy a Pananonic control board for fan around PJ? Or alternatively any shop that can replace the capacitor on the control board for me?  My speed 1 fan is turning very slow and seems to be capacitor problem.  Thanks.

I started looking at wall fans especially the KC4GR for my laundry area (small spot, 10.5 ft x 5 ft, basically for the ceiling I have a Houm SuperDryer so my fan will be on the wall).

I then compared against the Panasonic equivalent (well, the KC4GR is pretty scarce on the stocks) and found out its a 4 pole vs 14 pole motor design... with the KDK being more efficient in terms of wattage but still output similar rpm. What else I might be missing? Is it just a preference of grey vs white color...? well the Panasonic has a prettier remote control 

I converted the the kdk to m3/min, the Panasonic seems to deliver more air 85 m3/min vs 63 m3/min (2225 cfm).

Panasonic


KDK

What is the advantage of more poles in motor?
As the number of poles is increased, the magnetizing current of the motor increases and the motor can deliver the higher starting as well as the running torque. The frame size of the motor increase with an increase in the number of poles.

https://www.rcgroups.com/forums/showthread.php?2934319-motor-with-more-poles-give-more-torque-again More poles = electrical-/magnetic- or electromechanical gearing. At same electrical speed, the motor with 2x as many poles will rotate at half speed (hopefully at 2x torque for same size so power remains constant) also more poles will mean less torque ripple, so the motor will run smoother.
More poles, larger diameter motor gives more torque, and lower ideal speed.

Who are you? We should meet. Hahaha

Anyway I'm also looking for ceiling fans and was searching DC motors and their effectiveness. Hahaha. I've searched everything and your'e the one that answers the Qs I have in my mind.

If I had a strong steady fan I may not need to use the AC. Right now I use an NSB fan in my room and it's squeaking. When it's on low mode it's super slow. when the installer first installed it, they blades were upside down and it was always a lousy fan in general.

Are fans easy to switch out on our own?

so... which brand & model is breezy , and most importantly can go slow and quiet ? I wouldn't want something that can be too fast at no.1 speed.

will combine with air conditioner

Any idea how long these fans can last?

Want to ask about kdk v touch junior. In kdk website, it shows 2 star energy rating in the picture but 5 stars in the specification. So, which one is correct?

Seems like KDK and Pana also not free from problem nowadays.... and their high end fans are really expensive more than RM800+.... really worth it?

but this kdk K14XZ-GY shows 5 star even it is ac 

I changed out my ceiling fan!

I changed out my NSB Asta 56 with a Deka F5DC fan! The Asta only had 2 speeds and at low speed it was like it wasn't moving. Everything is made of metal.
The Asta was as heavy as a bowling ball and this F5DC is a lot lighter so it appears to be wobbling more than it should. It's silent though. It has a breezy sound. Not sure if I should worry about the wobble.
It took me many hours because I couldn't put my wires into the connecting board. I don't know why it didn't want to lock in. Everything else was quite easy. I'm not sure if I should install the balancing kit. I think the DC driver might cause it to be a lopsided on one side.

For Patah issue, many cases? Or you just heard only? So far I only saw one case and that rumours spread all over.

If new installed and got issue, just give Deka customer service a call. They will come to settle very fast.

so i tried to adjust the blades, still wobbling
tried to adjust the pulley, still wobbling. now when i look at it, it's worse
and my brown and blue cable fell out of the connecting board because it's not secure. i might just buy another connecting board to use. it's hard when to get it secured when it's stuck to the pole.

can the wire not send enough electricity if not all the little wires are connecting? the way i connected is like... i'm afraid it'll fall apart again.

sigh. there's a ticking sound now.

Do blades have numbers on them??

I think i'm an old school people not looking at fancy design but rather functionality. I got 8 ceiling fans in my house, all KDK brand.
3x Sensa 5 K15Z5-QEY - RM600+
2x K14Y2 - RM400+
3x K14YZ - RM300+
Those are the price 7 years ago.

2x Sensa 5 K15Z5-QEY and 2x K14Y2 is considered use the most with weekday roughly 4 hours per day at mid speed, and 12 hours during weekend served me for 7 full years now (accumulated 12k+ hours per fan), without having a single issue, not even bearing/vibration noise, speed wise remained same as new without capacitor change.
The cheapest K14YZ sometimes is noisy due to cover rattle and those were seldom used anyway.

So you get what you pay, but at least i have no regret with KDK fan, those are 'real fan' doing the job that supposed to do, my relative/friend who use those fancy/decorative fan already change at least once in 7 years due to noise/motor malfunction so at the end the cost even higher.

I heard alot noise problem about PANASONIC 56" BAYU 5 BLADES
Nowadays KDK = panasonic? Many people saying both is the same just with different case...