every mobo, processor, hardware have diff capability.... maybe ur mobo vdrop is large... so u need to increase ur voltage more than 1.406v which is mine.... increase ur FSB + MCH by 0.1v... loosen ur timing of ur ram and lower ur ram multiplier....

did someone say the red scorpion fan low rpm?

i was trying to feel the heat on my ram and accidentally touch my knuckles on the fan, and my skin got peeled off. kinda bloody too :S

okay fesick... got the chance to post edi...



this is with stock TIM... wait until u see TX-2




this is what it's like using TX-2 and just after my stress test...

really quite a diff between cap khinzir and Tuniq TX-2 ....

p.s: all test in run in room temp

This post has been edited by ham_revilo: Apr 7 2008, 01:47 AM

ur temp so good..
but mine..on room temp

same with bro ham_revilo at 1.31v:


at 1.34v:


increasing the vcore didnt effect much on temp?

edit : now i see the difference..(on load)

This post has been edited by fesick: Apr 7 2008, 06:39 AM

... lower rpm compared to previous xigma.. between 800-1500rpm

Yup...but its not selling in LYP yet rite? Only thru ckhoong.

yup true indeed.....setakat nie nampak dier sorang jerk yg jual.....

bro, actually okay edi... if i close my side panel, my temp will be around there and all of my test i did with my side panel open...

btw, damn good OC there.... 500mhz is off the hook bro

oh..me close the sidepanel..
my room damn hot right now..haha
the temp rise to 37-38c

ok... this is my latest test on 1.41v bios

finally free a bit time for fesick's request liao

idle


load

aduhh..why e8400 so kickA55 ah..
my finger gatal to get one edi..
but my mission for now is to change mobo..
want try push to limit this e6550 as my ds3 cant go any higher than 505fsb ~haha
btw,nice result bro tkh_1001..droooll droolll

erm... actually i am doing only 4ghz with 500x8(look at cpu-z)... ehehe....

hopefully i didnt mislead u

ur e6550 oso very good edi la... considering the vcore that it needs to push that far to 3.5ghz

still not many board can do more then 500mhz right??
anyways what board are u aiming for?? im thinking MARS as it really have good OC capability...

not sure yet..
yea,many people said mars ability in oc quite good but im more to dfi than mars..
later i rethink bout it..maybe hold first the board mission..haha

Huuu talking about peel off....not by xigma but stock fan.
When I put my fingers to it trying to feel the heat."zing" and my finger is pouring blood.

too bad for u guys.....got hand cut by spinning fan

u too?? actually i also pandai pandai wanna touch the heat pipe then ended up getting hurt by the fan blade but just small cut on my knuckle la... not really that bloody la...

Oh.......with tat kinda temp will it fry the cpu ler? Afraid to go beyond 1.4v..wat is MCH by the way?

actually imo its kinda hard to fry a proc as i seen ppl proc temp hit up to 80 but still okay... usually dont exceed 65c but i myself go up to 70c-71c with my stock intel HSF and my proc still working perfectly now...

MCH=memory controller hub... u may need to increase the volatge of MCH if u wanna go for higher fsb... lets say 500mhz but that doesnt mean u must increase it... some mobo doesnt have to increase the voltage and still hit 500mhz but those case are rare...

ps:correct me if im wrong...

This post has been edited by ham_revilo: Apr 8 2008, 12:51 AM

yup...seconded... u can always try increasing vcore n vdimm first... if those doesnt help to stabilise then only u start concentrating on tweaking ur Vmch or Vfsb....

heck i read at clunck forum saying that by increasing Vfsb n Vpcie u can reduce the vdroop for more stability

anyways.. just fyi my previous ds3 can do 500fsb also without touching Vmch,Vfsb or Vpcie settings just like bro revilo