only one person selling this s1283 (bulk), i'm 1st bulk and 1st one get the xigmatek s1283.

Putting dessicants will help, but as long as there is even 1% moisture there will be condensation at some point. However the temp range where water remains in liquid form will become very small, as the dew point will be close to the freezing point; few degrees more and become ice already (which is non conductive).

Its normal for voltage to drop during load, most motherboard power regulators will suffer from some vdroop, forcing OCers to need to set higher voltages than usual. Btw, if your processor voltage is fluctuating, don't blame the PSU first, the power regulator for the processor is on the motherboard, not the PSU.


If using duck brand PSU, more vcore will cause the duck to get roasted..
Cos processor now sucking more power from 12v rail..

It's weird no, often the high power consuming chips overclock well, like the Intel Netburst based processors and the HD2900.

Hard to say, lets do the math

Estimate your PC uses 150W(actually less, I run almost the same system as yours, and I run just over 100W on full load OC to 2.3GHz), and another 70W for a CRT monitor.

220W x 24hours x 30days = 158.4 KWH
1KWH is more or less 0.25 sen, so total is RM39.60 to run the PC at full load with monitor on 24/7.

Running on onboard graphics, its unlikely your PC would cost more than RM50 to run 24/7. With single GFX, then the cost goes up another 25-100%, depending on what card (also assuming the card is under load for at least 50% of the time). SLi/crossfire is what would really break the bank, I'm not sure even how to estimate for that.

Any1 have try to run windsy F2 with a vCore above 1.5v..?

I tried before.
Any question??

That time my clock speed should be 2.6GHz w that Vcore

-pWs-

wow.. 2.6Ghz w/o problem..?
I changed my cooler,then when i try to increased vCore ti reach 1.4,it always fail 3D mark 06.

Yeah...stable OR
Kinda miss my Windsy 38 F2
What cooler you use?? How much the temperature??

-pWs-

This post has been edited by -pWs-: Nov 16 2007, 11:35 PM

im targeting over 3ghz wif 1.568v...lalala
but now stable 2.909 wif 1.5v..
cant get 3 ghz yet..
haha...using stock heatsink and kipas berdiri dpan proc...hoho
set the speed to 3, then there u go....im flyin

hehehe....of course not stable at all...

Im using the AF 64 Pro.temperature 40c idle.

Is it good??

aiyaa
cant tahan nemore
im going to OC now,
meet u guys later wif the result
wish me luck. ..hoho(as if im going for war)
and also pray that i dont burn my proc tonite

This post has been edited by alive88: Nov 17 2007, 12:20 AM

1.5v Vcore should not be a problem for Windsor F2 if cooling is good enough. The Athlon FX that uses Windsor F2 runs on a stock vcore of 1.4-1.45v, it does come with a heatpiped cooler though.

This post has been edited by lohwenli: Nov 17 2007, 12:33 AM

selling brisbane 3600+ that can clock 3ghz .... =P

last night my vista ultimate got prob after multiple try on testing the capability of my ram., i bought 667mhz micron rams a couple of month ago but never got chance to test it. my D9DPN capable of reaching 850++mhz with 1.95v Vdimm...due to my stupid mobo, which limiting my ocing, thats the highest i can go...

guys, ever heard of chips FP-Y5?? is this got good overclocability??
coz with D9DPN, i can oc untill 2.8ghz for my proc.but with FP-Y5, can get 2.45ghz only..

is this caused of my D9DPN which need lower Vdimm to oc higher??

This post has been edited by rainingzero: Nov 17 2007, 11:01 AM

some review for FP-Y5 but in chinese~~

try see their result

http://forum.coolaler.com/showthread.php?t=149344

i just realize something on my system. x2 3600+ with ram div 533, isn't it suppose to be /7? currently displayed in everest ultimate and latest cpu-z as /8

ur rams is 667 right?? if u set cpu/6, the speed will be 667. if u set cpu/8, then it will be 533mhz...

i know that, but isn't 533 for 3600+ suppose to be /7 ? that's the question

FYI, oc n electric bill hv big relation, so its not sins to discuss that...
summore its still related wif AMD in this forum.. rite?

summore update to -pWs-

3800+ X2 windsor F3 | xixo_12 | TA-690G | Crucial 10th Anniversary | TTBTVX

[attachmentid=332123]
summore i realize know, my psu cant tahan when enter 3.5ghz zone..
there is a lot of flctuates volt..

This post has been edited by xixo_12: Nov 17 2007, 01:27 PM

Nice result you have bro.
May I know how much VCore and VDimm you pump?

P/S: Entries updating now

-pWs-

any one using Abit KN9 Ultra mobo ! i feel tis borad really bad , i cant pass bus speed 220MHz boot into window , sometime switch on button cannot funtion well , nth display on lcd , my previous was better than this board , i can pass bus speed 250mhz .. really disappointed change to this mobo ..