This is not the problem with the roller but the bracket that hold the roller bent slightly. Probably just need to bend it back to original position. The bracket that hold the roller does not looks like stainless steel tome.

yes there is, the wire at the bottom, you mean it is broken? But the closing and opening of the lock is still functioning, it is just the timing is out

This post has been edited by echoesian: Nov 6 2023, 09:21 AM

If I were you, I'd just replace hack all the tiles the side of the wiring, bury the trunking deeper and put new tiles on it. You probably cannot find same tiles no more but make it all totally new color would probably just make it look more artistic

If budget not allowed, then just one line of tiles to make it look like border.

There are boards that just sense the current surge on the motor as detection that the gate has hits its limit to shut down the motor instead of using timing to as when to stop the motor when opening and closing.

How many have tried the usb wifi RF transmitter. I bought from shopee now can control my autogate with OK Google.

Not the wire broken. Sometime the wire ware off a bit and power from motor cannot flow nicely so the lock will keep on up and down until reach the end when motor stop no more power flow trough then it drop down permanently to lock position. The center lock seldom spoil 1 out of 100

This post has been edited by dblcss: Nov 6 2023, 12:42 PM

if after grind off the welded ..screw can remove...after plate bend to good position ..fix back the roller and screw without weld ok ?after some times screw will loosen?

changing 1set roller with plate cost RM280 for my place ..

yes the bracket plate hold the roller slightly bent..
so far the plate still not rusty ...or maybe low grade stainless steel ?


thanks ....

Any idea how to fix it? Is it easy to DIY?

Use one pair of near wire connect from motor direct to lock. First must dismantle lock and remove old wire then only connect new wire from lock to motor. Then try open and close to check lock able to maintain unlock when motor is running. If once motor stop and lock drop down then everything shld be ok just replace old wire with new wire. Just attach new wire old wire then pull slowly from one end to the other end. Connect back new wire one end to lock and the other to motor. Then try open close that's it

Today I notice the wires look dented, could be broken. Can it be stiched together using black tape instead?

If still in working condition just joint it back and black tape. Then try open close and if the lock perfectly then just continue using it.

Could someone pls suggest a brand or company that offers a complete set for an automatic gate, including both the gate and the motor? I'm new to this field and seeking recommendations.
I prefer the functionality could migrate with, IR, switch panel, Wifi , HomeAssistance etc.

do you know how to temporary program to disable the central lock?

Hi
If interested in full aluminium can whatsapp us at 0122019294

This are few gate that we done for LYT forum customer.

Custom make type
https://www.facebook.com/100001210351987/vi...026781351004262
https://www.facebook.com/photo?fbid=6404198...404209249629357
https://www.facebook.com/photo/?fbid=600058...000594663324153


Ready make type
https://www.facebook.com/photo/?fbid=630865...308665625850387
https://www.facebook.com/100001210351987/vi...896460648459476
https://www.facebook.com/photo/?fbid=600442...004431159607170

Just remove the holding on the left hand side gate by unscrew it out.

I bought an aluminium gate from this forummer for my Bangsar Baru house.

Very happy so far.

Bought nearly 2 months now?

This post has been edited by Garysydney: Nov 8 2023, 05:39 PM

On the motor?

On the gate

Being quoted RM29k for this 18f Delux gate
Really not cheap
Was wondering if got any other alternative brands that offer similar product?

where is it? Got any photo?