i try ATI Tray Tools. but dont have also.. btw.. im using Colorful 1950 GT 512MB 256Bit Graphic card.. still have any software to detected my VGA card temp?

yeah, especially when u are running stuffs tat needs more power than ur psu can supply
usual culprit will be gc, especially the high end 1

here's the scenario....My compaq PC comes with 350W PSU, with 1 harddisk, and 1 CD ROM.
Myself upgraded:
1. Additional 1 Harddisk
2. Additional 1 DVDR-ROM
3. Additional 1 PCI Modem
4. latest addition : long hours of torrents

I used to experience "hang" within the Windows Explorer. now, with my brother constant torrent, the whole system hang. I have to actually reset the whole system.

So, confirm PSU to be blamed??

yep. get the higher power CPU to suits your usage.

i dont think the problem is PSU...

hard to diagnose just like tat
psu might just be 1 of the reason
there's a lot of reason ur problem might occur, such as corrupted os, memory conflict, gc overheating
how about u try reformating ur os with a clean installation?

hehe.. its is ddr2 667..

nyway.. can nyone explain to dis super noob about da things i ask b4? still confused..
&
1 more question..
if da mobo support up to ddr2 667.. but then i install ddr2 800.. wut will happen? does da ram running well?

hi, wanna ask that, is there any infrared remote control for PC in the market IN MALAYSIA ?

if there's none, is it possible to make one? i got an IrDA receiver which is quite useless other than transferring data,

wanted to use to play/stop/whatever when listening to mp3

I think there's a PC remote control for sale somewhere in Garage or Bulk section....

shouldn't be a problem, it will then just run at 667

Use your phone to control the pc with bluetooth. Works for me; nokia wireless presenter.

How to determine the chipset of RAM modules?

Ok here is my question,my ram is ddr2667 running at dual channel.When I open my cpu-z is seems my ram frequency is running at 315 instead of 333.What's the problem.My rig is stated in my siggy.Thanks alot people as I'm still quite new to computers.

To determine ram chipset you can try looking at the chips on the ram.You will see the manufacturer of the chips stated on the ram stick.(Correct me if I'm wrong)

This post has been edited by Nemesis181188: Jul 25 2007, 12:43 AM

What brand PSU was that? i opened my brother's PC (hewlet packard) and saw FSP installed inside there.. real power on ordinary PC...
ur PSU might causing the prob, and maybe not..

I forgot the name already, i'll check back when i go back home this weekend. it's definitely not real power and it's also not from any famous brand that i know.

since u r using DDR667, the ram's frequesncy is CPU/6, where 2200/6 = 366.7MHz
so i guess either;
- u enabled the CnQ
- u set the divider to DDR533, which is CPU/7 = 2200/7 = 314.2MHz

noob question again ... ..i have 2 80mm fan taken from dead psu ... can i solder together the red and black wire from the fans and then solder it again to used 4 pin molex so i can use only one 4 pin connector from psu ... i hope u guys understand ... ...then will the fan run on 12V speed or the speed of the fan will be lower than 12V speed ... anyone?

This post has been edited by sang_karim: Jul 25 2007, 12:34 PM

my noob question:

RAID0 mode = not RAID right?



taken from here.

what is our CRT contrast ratio?

u mean solder the wires of both fans to ONE 4 pin molex?

if thats whay u mean, then yes can...i did the same thing to my dead 80mm PSU fans... 2 fans using ONE 4pin molex. and they both work at full 12v.