1 question

what's your ram? D9GKX ram chipset also rite?

some ram/cpu dislike overvoltage.. that's for referrence.. since different hardware got different setting..
sometimes bios also being a culprit..
check HT Link Width if any either 16bit or auto.. sometimes auto option not work well..
sometimes cpu need more voltage for different ram settings.. for mem controller maybe..

good luck

oic, i thought you dun understand that concept? Look like you also understand but just purposely crap here.

If i dunno how to set those stuffs, do you think i can reach 1200?

Please answer my question, you also using D9GKX ram rite?

yup.. it's just bare KVR
and i observe D9GMH need more voltage..
D9GKX can do good tight timing..
if possible i'll set for lowest voltage but better performance..

---

Added on August 15, 2007, 1:32 pmi don't mean that u don't have any idea about it since u can play with the bios..
just my latest bios.. sometimes will reset that HT Link Width into auto eventhough already save 16bit..
just check the options may sometimes we mislooked them..
but ur mobo is different with mine though..

This post has been edited by 8tvt: Aug 15 2007, 01:32 PM

Gratz
Change processor again

-pWs-

Thanks

ya, coz feel like wanna try CZ proc badly , see how high can OC with it

also , need a much more powerful proc for programming stuffs

This post has been edited by dblooi: Aug 15 2007, 02:24 PM

wow...damn it lar...
CZ r so tempting...
even the new biostar mobo so tempting...
i'm lack of vdimm la...

b4 that i was using brisbane, with the same setting i couldn't hit 1200 no matter how hard i tried.

With this 90nm F3 windsor, just some simple tweak already hit 1200

you are right, brisbane integrated memory controller really crappy

Yea. Brisby really lacks of something.
1200 really nice la. We should organize 600MHz clubby d

-pWs-

More updates.........Ive managed to get my proc up to 2.9ghz but it wasnt stable for any stressing. Best so far ive got is 2.8ghz @ 1.36v . Btw I noticed that the core voltage drops a lil when i start stress testing. Also whats the highest I can go on voltages without risking an immediate burnout? I'm still using the stock cooler

Stock cooler maybe 1.4v max
Change cooler, bro. There are a lot of good coolers out there in the market.

-pWs-

not only voltage, must keep a lookout for the temps. 1.35v using stock cooler, my load reach 67. So i decide not to go any further. Just got a new hsf today, so hopefully I can breach 3ghz!

is time to grab some d9 goodies

Haha. Poor bro

-pWs-

haha , save some money 1st ..

any one having problem with TA690G AM2 temperature reading?
mine show Idle 26'c and full load 29'c only. any way fixing this problem?

same goes to my Smart T-fan utilities control only show CPU & System fan reading only, even I have install speedfan 4.32 still no reading on the fan speed. ( btw I got 3x12CM connected to mobo fan header) Stock Lian LI each 1500RPM and Vizo 2000RPM

This post has been edited by beast921: Aug 16 2007, 03:52 AM

Haha...i got good experience with temps lastime with my manchester 3800+. That was 60+ at 2.6ghz ady Haih.......can boot at 2.9ghz but must set voltage to 1.4v. Prime fail after 5 mins coz temp reaching 65 ady . Must get better cooling.

Btw....whats max voltage i can pump to my team value ram???

---

Added on August 16, 2007, 2:47 pmHmm....my board also has a similar prob except with the readings for individual cores.

This post has been edited by joe_star: Aug 16 2007, 02:47 PM

there has never been a single utility that can read Brisbane temp properly, trust me.

i have 3600+ brisbane with msi k9nu neoV, using raptoxx 550W, why in bios i can just set vcore to 1.3V? because of the limitation of mobo or ... any suggestion??

It looks like more to mobo limitation. Not sure if there's any hidden features or locks though.