where to get the reservoir? @@

This post has been edited by Ryoga: Apr 5 2008, 06:04 PM

@Ryoga

U can ask bro MetalZone.... He has da same model I think...

(No need 2 quote da whole picture laa...)

oh my god, oi use spoiler la.... then its better..

This is mine.... Juz finish fix it....Then suddenly da yellow Y-coupling crack.... Whoaaa.... Banjir...



Will post up da rest later...

clamped to tight on the Y-Coupling? steel worms clamp will cause some damage if clamped too tight.

Well...i think it bocor b4 edi... Bcuz when i 1st install, it leaked....so i thought i did nit clamp thight enough.... After tightening da clamps, it work fine 4 da past 4-5days... Yesterday only i notice y suddenly heat increase, got bubble sound in da pump n my t-line empty....

luckily u didnt spoile anything, leakage is dangerous...

Yup...luckily... Bcuz all my hardware r not on da ground....juz my neon got wet...

last time i killed my 7600gt cause of leakage , luckily i got mine rma'ed and sell off with the new card...

lol ...post up ur WC pic.... I wanna c... U using dual loop rite???

yup... currently doing cable management, wen done will post here lagi...

I wanna try out WC and was wondering wat's the different between the CPU block which have 3 hole and 2 hole. Which 1 better? I was thinkig of getting parts by parts before i start building up the WC. Any suggestion? i was thinking of WC my cpu, northbridge, GPU and ram too if possible. Wat else can wc? what is the rating of the pump that i need? How many radiatior i need? My spec as in my siggy =) thanks all sifus.

helo... it been a time i visit this thread..... i miss those wc times....

now just use tuniq tower 120....

This post has been edited by amd_hardcore: Mar 15 2008, 01:25 PM

will get my wc real soon~



still in process searching 4 da best part~

im getting new wc stuff too.. but i will cover my gfx with some clothes to prevent it getting wet is it ok to do that?

Bcareful not 2 short ur GC....

what u mean by short my GC

just make sure run leak test properly b4 turn on ur PC... normally a proper installation shall prevent leak...

hmm i see alot of ppl retiring from WC... wonder why?..

as a WC user myself,
1st of all, maintainance problem, takes lotsa times clean the loop...
2ndly, spend longer time to re-setup the loop if making change in hardware such as mobo.
for me myself, spent 10+ hours to resetup my rig from amd to intel c2d cause of time wasted on WC including rearrange all setup such as remounting blocks, cleaning radiator, cleaning blocks etc.
tougher cable mangement when adding hardware once the water cooling is done inside a case.
lot of hassle, need maintainance from time to time.... and also a risk of leaking if pump death, but normally shall be ok for 24/7 if loop is setup properly and leak tested.
Lastly, just some noticable increment over high end air cooling such as Thermalright IFX-14 + lapped base and IHS, i think at load temps its juz cooler than the IFX-14 or Xigmatek by few degrees, less than 10c i guess as my setup temps are quite high after several times of waterblock remounting and the thermalpaste seems spread correctly. my E8400 reaching 66c@4.05ghz@1.4125vcore(BIOS) at freaking hot room temp of 33c-35c at Cyberjaya during super hot noon, 56c at midnight(Full Load), from the result we can see that ambient temp does affect WC alot. and also the load to idle temp drop faster than air cooler. I saw a huge different when changing my old amd x2 proc to air cooler (CM GeminS), it cant even near the performance of my WC with GC at the same loop.
mayb i was on 10v downvolted pump and low cfm fans for the higher load temps.

This post has been edited by lichyetan: Mar 30 2008, 03:52 AM