D-Tek Uni sink could work on MCW60 ??

How does it works ???

A bit curios about it ...

the zalman ram sinks for 8800 series that meant to work with zalman gpu block looks cool too.. wonder who sell it... should be able to fit with swiftech mcw60 with some mod maybe...

it should work as teh clearencewhere the barbs are is very suffu\icient... uni sink basically is wat the names says.. one heatsink for all the heat producing chips. best thing about it is that its held by screws.. not thermal tape... basically any block similar size to the dtek gpu block should work

My 1st WaterCooling PC.


My WaterCooling PC

Cool-Trek DP1203 or Alphacool NexXxos Xtreme III or Swiftech MCR320-QP better?

All three are about the same... the main difference would be their barb location as well as built quality.

I personally would suggest Cool-Trek or Alphacool NexXxos III ...

coz those have better finishing quality ...

i had a question here.,can d-tek db1 pump cooling both GPU & CPU at the same time?

It sure can ... it's D-Tek that u are talking about men ...

One of the best brand for water cooling stuffs ... the pump may not be the strongest but should be enough for GPU and CPU loh...

i'm very new in wc world.. just study about wc last night..
i have a question.. can this devices make a great performance for my CPU...

1.d-tek fuzion cpu block
2.swiftech MCP350
3.swiftech MCR120-QP / thermochill PA120x1 (recommend me which one the best)
4.swiftech MCREs-micro
5.clearfex tubing 1/2" (recommend me how long) for TT Armor(back side rad installation)
7.gigabyte coolant (blue)

correct me if i'm wrong or what eva..

Its good

Definitely perfect dude .. .

One of the best performing set .... however it would be recommended to grab dual rad rather than single rad ... .... ///

performance is undoubted ...

<--- prefers triple rad... for maximum cooling...

it is? bcos i just wanna make loop for my CPU....how many cash do i need for that devices? it is available at any store/lowyat? i never see swiftech etc brand at any store/lowyat

i'm facing an heat up problem with my graphic card. any recommendation on which cooler is suitable for my X1900GT? the temp is 64 degree with a 80mm fan pointing at it. without the 80mm fan will be 66 degree.

@amane_kaoru
Grab Artic Cooling Accelero S1 .. cheap but very good performer..

Accelero S1


@book8
It probably cost about RM1200 ...

Depend on the radiator chosen ...

However u can't get any of those in shop .. u have to order from bulk order ..Metalzone would be a guy that has almost all the items in the list .. .

It would definitely enough for CPU ...



@IcEMoCHa

hehe .. however mounting 3x120mm rad is very tough ... lots of things need to be at the right place ...

dual rad definitely enough amane_kaoru ......

@Doom, thanks. well, i was planning to use a water cooler. is it really safe to use water inside a pc? wouldn't it'll leak after some time??? i just scare it'll leak and is it easy to apply?? i wanted to overclock my system but still lacking of a great cooling system. any recommendations for budget below RM300??

I would rather not to venture into water cooling if budget limited ..

with that budget better grab high end air cooler due to lower risk and better performance than low end water cooling ...

how about to uninstall the WC.. i had no idea how to dry the coolant before unplug the block.. and how about Gigabyte 3D Aurora II WC? i wont ask about TT WC because i seen many user fu*k that brand WC..


This post has been edited by book8: Dec 6 2007, 11:29 PM

i just tried to overclock my CPU again. at 1st, i try to set it 3.0 directly but it crashed then i try to overclock it step by step from 2.6 > 2.7 >2.8 and> 2.9. once reach 2.9 Ghz, in the BOIS hardware monitor, the temperature raised till 57 degree. then i reduced it back to 2.6 and the temperature drop back to 47 degree. what cooler should i use for overclock it till 4.0 Ghz? i checked my board, the highest Voltage available is 1.450V but i'm currently using 1.400V. is 1.450 enough to tweaked it to 4.0Ghz?

At last i owned it