Maybe add bit more voltage or try loosen the ram timing?

If not try clear the CMOS and OC back to the desire speed and Memtest it again. I usually do that juz in case i mess up with the settings.

Only today i realised that i'm using Hynix D43 ram after using it for 2years+

---

Added on August 19, 2007, 11:18 amCan anyone tell me actualy my 9800PRO is using R350 or R360 core?

Cos on the device describtion i get this :


But then the GPU properties i got this :


So... which core my GC is using? i dun wanna dismantle the HSF

This post has been edited by ac_N1: Aug 19 2007, 11:18 AM

The only way to identify ur GC core is take off the heatsink and look at the chip. As for my case, the windows detected my 9800PRO with R350 core but actually on the pbc board my card is using R360 core. So, there is no way to identify actually what core ur using with software unless u take physically move by take off the heatsink and look at it.

This post has been edited by fylon: Aug 19 2007, 01:13 PM

i think 360 is for 98xt. hmm......the most comfirm way is take off the heatsink and check the label on the gpu. but does it really matter?? if it is 9800xt core then its possible to flash it to 9800xt. Ofcoz have to make sure your gc can run at 98xt speed.

Yea. The is two batch of 98PRO card, first batch is using the R350 core and the later batch is using R360.

As if the card is using R360 core, and have the thermal sensor chip then is possible to soft mod it into xt care. Search over the net then u will find the article tells about this card and how to mod it.

traded my s478 for s775 yesterday but still sticking with agp n ddr

I already plan to softmod it..... I'll dismantle the HSF tonight Hopefully it's a R360 core

Hehe.. I was owning a R360 and moddable 9800Pro now. Plan to mod it into xt. Do check this before u do any modding task. And must change ur hsf as well. Im on my way to mod an old AMD scoket A heatsink into my gc heatsink.

By then, try OC ur gc til xt speed and run benchmark see is there any artifact on ur card when running on xt speed. If there dun have any artifacts means ur card is able to corp at that speed.

LOL, I've particularly maxed all the voltage settings that the board already has, except the processor.

I think the motherboard is limiting me, running with dividers also gives me the same problems.

hmm.you should be getting better scores with your 6800GT.mine 6800GS scored 10101 in 3dmark03.but my card's the 128MB 128bit oc-ed version.clocked at 450/1200 stock.

whoa.how much is one stick?those are some rare gems.


hmm.just checked with CTIAW and it says PAT-mode : Fully enabled.and my memory read bandwidth is 3548mb/s @ DDR274.

crap..after testing asrock 775i865gv i found that it sucks..stupid mobo..guess i'll have to send it back n take my s478 mobo..but at least its better

This post has been edited by Mooneyes: Aug 19 2007, 06:15 PM

Haha.. Trade back ya s478 system ba! S478 far more rock then LG775 eh!

Btw guys, wandering a question. I prime my system for more then 36 hrs and 1 error found. Is that means my system wasnt stable? Was using the latest version of ORthros, running at pariority 9 stress RAM and CPU. This what i get from the log. Does my system stable?

FATAL ERROR: Final result was 418CB13B, expected: 248EF622.
Hardware failure detected, consult stress.txt file.
Torture Test ran 36 hours, 57 minutes 51 seconds - 1 errors, 0 warnings.
Execution halted.

P/s: I just found that my ram cant be tighten up anymore. Restart several time when i tried to tighten the time from 2.5-4-4-8 to 2.5-4-4-6. Guess gota leave it stay at the loosen timing.

Edit: Typo

This post has been edited by fylon: Aug 19 2007, 10:42 PM

i just found the software to enable pat!!!

dunno right or not...
here the link!!

http://www.cpuid.org/download/Tw865.zip


this is the forum and maybe new version upload already:-

http://www.xtremesystems.org/forums/showthread.php?t=43926

This post has been edited by GCI99: Aug 20 2007, 12:56 AM

It's good, but I think MemSet is a better alternative since it has a wider range of options.

those are very old tools already

yup, very old tools but able to enable the PAT. i prefer memset. can set it in startup and no need manually set everytime start pc.

Memset aa...so once set it no need to set it again like Tweak865? gonna try this later .... thanks for the info ...

have to go through the readme 1st la. act just save the file and create shortcut put in the startup folder then pat enabled(partial only la) already.

ok ... will try it later .. if got problem ... i'll ask here for help ... but it doesn'e that it will fully PAT enable rite?

quite hard to fully enable the PAT la unless we do the bios flashing to hack the PAT. still looking for the comfirmation on flashing p4p800 bios to my puny p4p800x