Thats measurement between screw hole. Normally we measure for whole fan body...exp: 12cm x 12cm x 2.5cm..

nice idea. just what is in my mind actually. gonna do it later.

So where should I measure?

---

Added on May 9, 2012, 9:20 pmThat is amazing! Do you have a process on how you modded that case? Or even the before picture..

This post has been edited by BenSow: May 9 2012, 09:20 PM

For so normal 120mm fan, the size is 120mm(long) X 120mm(width) X 25mm(depth). Refer HERE for guide.

Don't have la bro...don't know how to start the worklog here. I'm not expert in writing essay....hehehe

haha not even picture before mod? Wanna see how much change there is..

---

Added on May 9, 2012, 10:38 pmSo standard is 12cm x 12cm x 2.5cm la.. the length between screw holes doesn't matter?

This post has been edited by BenSow: May 9 2012, 10:38 PM

Have, but only for own record . I just take few example from any modding worklog here which suit my taste & implement it to my case..
This is the original look btw..


Actually the depth sometimes is different...like Delta fan is thicker, 38mm i think.. Yes, we not measure it by screw hole distance.

This post has been edited by kherel77: May 9 2012, 10:42 PM

120mm try Yate Loon D12SH, Cougar Turbine 120

200mm dunno

Is the cooler master neon LED 120mm fan still available for purchase? Been searching high and low for it but to no avail.

Why not consider other brand? http://forum.lowyat.net/topic/1014899

Oh, because the LED position on the cooler master neon fan is in front of the fan blade, so will be nice if I install the fan above my casing.

hye guys..i use an old hp casing which only has 1 exhaust fan...would changing a new fan do any good or would it be better for me to change casing..? my hp casing is quite small and it gets pretty hot sometimes esp my GC...went up to 50+ even when im not gaming..( is it normal?) would really appreciate the help..

budget would be 150.. tight budget, thanks in advance

Looking for a silent 120mm red fan with the same colour as aerocool shark red devil

http://www.aerocool.com.tw/images/fan/shark/red12_all.jpg

HP chassis?? u mean the pre-assembled PC right? would be hard to change the chassis considering all the components are made to fit snuggly inside... and yeah will not help much by changing just the fan.. maybe adding an exhaust at the top?? need to modify though

---

Added on June 25, 2012, 9:52 amwhy not just get the Aerocool Red instead?? why look for an alternative?

This post has been edited by Clem1982: Jun 25 2012, 09:52 AM

Looking to buy a case fan to put on top my HDD to cool it.

Can recommend a brand for budget & quiet? TQ (RM10 -RM15 ?)

This post has been edited by alvinfks78: Jun 25 2012, 03:42 PM

Hey guys, is ArcticC F12 pwm less noisy than my Xigma XLF-1254? I need something quiet

Too noisy on the fastest rpm. I can use a voltage reduction cable but it's a little slow and cable management might be a problem

But anyway, I m considering it

Not sure about the XLF but I have an artic f12 and it's quiet

Am really attracted with the F12 because i find my XLF too bright, while my bed is just next to my desk. I feel like sleeping in an Aquarium with lamp, you know la XLF-1254 white led shined exactly like an Aquarium. And as well with the noise issue. Am thinking of moving the position of them and somehow probably will reduce them ?

Ahhhh similar situation here. Thinking of getting Red LED lights but tak boleh tido

You can go with f12 pwm for all your casing fan, quiet and powderful but no bling bling

hey guys,
i want to replace my 140mm coolermaster stock casing fan,
any brand with led, low noise...
any suggestion?

My aquarium that inhabit some cicak



Note the proc fan and rear exhaust fan. That two fella are the culprit, so the plan is to move both up as exhaust and replace 2x AC F12pwm to their position.