Just came back from the talk with Proton CTO. I have informed them of those 5 issues. As for issues like the key, they will investigate it. Reverse sensor they said that they recently got it fixed so u will need to change ur sensors. Iirc, they said they fixed it on June this year. Other issues brought up during the talk by others which I consider major is they complained that after ECU/TCU update which fixed the jerks during start/stop has caused a max speed limit of 160km/h.

I recorded the intro session and the Q&A session and I will need time to process it. What I can conclude is that despite initial things said by Proton where they are using a lot of Japanese tech for the car, during the talk, they said that most of the tech is German tech and standards(not saying that because its German tech means Proton = BMW/AUDI/VW etc) with slides that shows the company that provides the parts and he explained European car standards.

Syabas Proton.

May I know what did they say regarding dashboard rattle?

Actually the pain sekejap only lor, hahahah and then look at the car say: "Ahh, rasmi already"
but small matter la, not so deep oso, just paint come off, lucky no cracks!

yup... *anticipating* as well...

wah... sakit sakit hati... bad or superficial? I had some idiot accidentally stained n scratch mine at parking lot...
went to buy scratch remover and it worked very well, the scratch is not to be seen even after searching for it

A bit bad la, but not noticeable till you actually stand right in front of it. I think those scratch removers won't work on mine, cause mine scratched till paint come off ady, but at least it's the skirting part, can buy a whole new skirting, same colour also, to fit back rather than waste time to repaint the whole thing, sometimes paint oso diff colour.

During tightening process, the dashboard will go to its natural shape. When the dash is first installed, its not yet in its natural shape yet so once it forms its natural shape then it needs to be tightened again. He gave an example like when they manufacture a shirt it needs to be ironed first before it forms its shape(im assuming that he means forms the crease for the hands and shoulder area as well as the sides). He also said something about the plastic going thru the stress release process.

If wanna save money the RM5X Ezy Touch Up paint does the job with the correct colour. I'm using it at the moment and it works as advertised. The colour is also correct.

Where can I buy that? search high and low in the car care sections in most stores but can't find
Genetic silver colour?

This post has been edited by Cwkc93: Sep 13 2015, 01:19 AM

Jusco. Search the automotive section. Its normally on those cardboard shelves. I know the one I bought at even had a small screen to show how to use it. Yes they have that colour and I have bought it before to repair some paint scratches.

Dear yadea, may i know what is wrong with the key? I have to know before i proceed with the FMEA.

Some of the item from german's:
1. Brake system ZF TRW germany
2. Engine management Continental germany
3. EPS Bosch germany

This post has been edited by pocue: Sep 13 2015, 01:42 AM

I failed to follow up on that. What happen was they acquired someones someone's key to check and asked that person to go to his office after the event to get back his key. I should ask the president of PICM on what can proton do. After the talk, outside, one of the proton staff asked me what problems I have with my car and he took my key and have a look and said they need to check. He took out his car key(of another car) and said maybe cuz his key fab is thicker(which I dont think its the case).

[quote=yadea,Sep 13 2015, 12:46 AM]
During tightening process, the dashboard will go to its natural shape. When the dash is first installed, its not yet in its natural shape yet so once it forms its natural shape then it needs to be tightened again. He gave an example like when they manufacture a shirt it needs to be ironed first before it forms its shape(im assuming that he means forms the crease for the hands and shoulder area as well as the sides). He also said something about the plastic going thru the stress release process.

means another trip to SC... can I just show them yr post since its a response from Proton itself ? save time on diagnostics

U can try but since im not a proton representative or even from proton then I dont know whats the outcome. I am just conveying what the CTO said.

This post has been edited by yadea: Sep 13 2015, 12:31 PM

You can also buy online. Just google ezy touch up and the link to their website is the first in the search result.

I bought mine from there. Make sure you select the proper color code.

I touch up both cars as both got scratches. Quite a good product.

Ahh thanks guys! I shall go for Jusco first to have a thorough look and if still can't then i'll buy it online!

hey all, just got my car three weeks ago. Has anyone experience any problem with the USB port? It was working fine previously but yesterday it doesn't charge my phone and doesn't seem to be able to detect it, sometimes I'd listen to my own media files from phone when I connect it via USB. :-/ anyone?

how long did u guys wait to get your car? can i can get it in less than a month of waiting period?

Your loan approved?

tried resetting the head unit yet? might be able to solve your problem. Below your power button there's a clip which says "connectivity" , open it. Below your SD card slot, there's a small hole that will allow u to poke a pin to reset the Head unit. Hopefully that helps

I'm getting an axia, sa told me will get the car by end of Oct. I need to use a car by first of Oct. So I'm thinking of getting iriz if its fast.

My loan for axia already approved