hmmm ... i can SMS them for the availability. mind to tell me why u are looking for it ....

yah much more better, u coudl tie the PCI-E cable and the sata power cable together for better alignment.

Push the power, reset cable and bit more behind the HDD cage so that not that visible, why dont u use the Q-Connector comes with the Asus mobo for easier assembly. Do u really need the rear USB ports ?? it's kind of too visible laying at the bottom of the case..

---

Added on April 30, 2007, 10:43 am

it depend the type of the casing u are using, personally i like BS-02 more due to it's flexibility of reverse mount the fan either for intake or exhaust.

I turn it into intake to reduce the temperature of my 8800GTS and it turn out to be 5c lower for both idle and load as compared to exhaust.

It has another advantage as well as it's slidable so it would be more flexible and it would not drag the hot air around the case back into it.

I reversed the BS-03's fan become intake and it suck the hot air exhaust by 8800GTS back into the case.. 

Hmm today go check for the fan. coolermaster super fan airflow not bad.

But just now i try remove my LL case and feel the airflow of LL fan, i feel like quite high airflow than normal case fan.

i also thinking the same...coz, the filter's hole is just too small...maybe the air dont flow out as much as without the filter...but,the filter suit me as my place is full of dust!!!same with ya,akachester.....

off topic...can i know how much do u bought the zerotherm vga cooler...and where do u bought it? (wat shop in SLS)

Not really. Stronger fan also means the filters will get clogged up faster since more air is moving through it. You'll still have to clean them up regularly.

In my own experience, using low airflow fans actually work well because dust it not easily pulled into the filters since the pressure from the fan is not very strong. I'm also using double filters in my PC-60B. One is the stock black foam-like filter, and on top of that is a aluminum mesh filter (from Petras Tech, MNPCTech).

Today search around Low Yat for replace my LL case fan, but most of them are vizo and coolermaster, air flow i think is same as LL case fan besides vizo's windstorm ( dam noisy if i put 2 of them ). So i think just use back LL's fan until can't work then change.

I saw 1 aluminium fan quite nice but no 12cm, performance around 37 cfm and noise is below vizo UV Led fan.

SLS? where is it XD. that Artic Cooling fan look like nice o XD

I'm using Yate Loons undervolted to about 1000rpm and they pull air just fine through the filters. Too much pressure can be decremental as well you know.

Give it a try and see how it goes, for all you know, your temps might not change and you'll have a quieter rig.

anyone managed to install the top 80mm fan for PC-G7?
i tried but looks like my cables are disturbing it..

or should i put nothing on it? 

Won't it produces noticeable noise .. ??? I had assemble P C for others based on their requirement ..... I came accros of VIZO fan before but. It pushes high airflow but at higher noise level of course....

I just can't get used to it ... even CM silent version i feel it's a bit noisy when placed at the front panel ...

What for lar buy casing wheels? U wanna drag your CPU around your room everynow and then? 

nah still can mod it using magnet or screw

the plastic material use inside lian-li casing is very low grade. even my dust filter frame also can notice slightly cracked due to heat.

anywhere, my casing lasted longer than i expected.(bought in 2001)

even the new lian-li casing still using the plastic clip??? that's just suck.

one thing for sure, u can get a full alumunium casing under RM300, while other brand u need RM450 and above.

alluminuim advantage over SECC steel, they dont get rust and absorb heat better, easy to mod(*), lighter. so u can use them like year(s)

Today suddenly have the temptation to take out the front panel and do some mid-afternoon casing cleaning. Check out the dust collected at the front panel!!! It's only 1 week+ since I last clean the filter.

[attachmentid=236109][attachmentid=236105]

Followed Doom's and few other Lian li kaki suggestions to remove the rear mesh filter and replaced with grilled finger guard instead to improved air flow.
Results : Seriously better air flow! and Slighly lesser noise...

About the new PC-7S, it still does have the plastic thing..

mADmAN can i ask 1 thing? I ask at many thread also no 1 answer it.
If put the filter like yours is it will block some air flow ?

yeah its mine....but that pic was taken when the case was still brand spanking new...ive removed it and replaced it with a fingerguard (now using one on each side of the fan)....the mesh thingy has only seen like 3-5 minutes of airflow
then u should get this from uglyvamp...



its good in filtering and doesnt block out so much air flow...im using it for my fan on my XP-120.

reason why im not using it on my front is because my room has a lot of dust and i need something thats easier to remove and clean. if i use the one in the pic i have to unscrew it every time i wanna clean it off

i just saw the aerocool brand only...
nvm,will check out again next time....

also, i dont see any vantec nexus at lyp...

depends on ur hardware temp, is ur proc hot? is ur vga hot?

if both of these hardware are cool in temp, don't bother getting additional fan, it doesn't mean if u add more fan in ur case, the temp will drop like crazy...

example if i got 10 intake & 10 exhaust fan doesn't mean my hardware will get the same temp as if i were using watercooling, hell if its works, i think some of the watercooling users will opt this option coz less hassle in managing it, have to monitor from time to time to make sure no leakage & yada yada yada....

although u got 3 exhaust fan (PSU Fan + FM121 + FM82) sucking out all air inside the case, it's not like ur case is "kedap udara", fresh air will eventually get in by those crack or tiny holes, don't worry lor

if ur hardware is hot, it means the hardwares are hungry for fresh air

if ur hardware already in an acceptable temp range don't bother getting an additional fan --> if really wanna add more intake fan, prepare to reschedule ur cleaning time table for the case

akachester your Proc nad GC is is running on that temp or idle ?
My hardware temp also be like that for idle.

Now i also got problem with the fan sensor, 1 is side panel fan, 1 is front intake fan, i dont know where to put my sensor and just hanging somewhere. Maybe need install that fan control to control myself, because that sensor hanging ther although is hot or cold also run that RPM, any suggestion where to put my sensor ?