yes I noticed that, hence the "general failure" ping result
I suppose this Dlink DSL-2730E modem is a half-baked product in terms of IPv6 features.
My PC could only utilize IPv6 only in bridge mode.

Every other connection methods failed to advertise / delegate the IPv6 to the PC.
Be it SLAAC with/without DHCPv6 or RA

Before I upgraded to Unifi, I was also using the TM-supplied DLink DSL-2730E.

In Streamyx, I could not get IPv6 to work even though the firmware "supported" it.

well when I was still on streamyx i did configure my router into bridge mode then setup pppoe from windows

able to obtain ipv6 without any hassle

I shall rest my case for now...
hoping Dlink will issue a firmware update or perhaps I should get a new modem ..

Weird. Mind to share your location? Cheras, PJS, PJU, KL, Setapak ...?

anyone having difficulty to download apps on iphone ? :/

*am using unifi 5mbps

This post has been edited by dannykhoo17: Sep 10 2014, 12:41 AM

What is this ipv6 all about? Ever since i rebooted my router yesterday. My popcorn time can't work anymore. Downloading at 16kb/sec instead of previous 800kb/sec

This post has been edited by Intrigue: Sep 10 2014, 01:58 PM

Issue resolved. Disable the IPV6 settings at my router and voila... back to 900kb/sec

Seremban

my home streamyx got a problem, my laptop and other devices hard to connect to wifi, eventhough it ady show connected but still can't surfing internet and sometime some of my home device can connect and using internet but my handphone show network error~ any sifu here noe how to solve it? my friend said is due to same ip problem but i dont think so bcos when only one laptop connect still gt tis problem appear

Disable!

something is not right

I have both TM Riger modem and TP Link modem, both MTU set at 1492

SLAAC

some of websites are not reachable or extremely slow with ipv6 on TP Link modem

but with TM's Riger modem, ipv6 works almost 100%, all sites reachable and fast speed

whats the cause? firmware problem? I don't see anymore advance setting for ipv6 have differences compare to TM's preset


different router use different MTU ? or what

This post has been edited by squall0833: Sep 12 2014, 01:31 PM

I'm in Bandar Sri Sendayan on Streamyx 8Mbps. IPv6 address obtainable but can't go anywhere . I've tried Windows 7 PPPoE dialer with IPv6 enabled. I can see the address assigned but ping -6 or tracert -6 (or -d) won't go anywhere and stuck there. Tried with pfsense, mikrotik, openwrt (all of these on Virtualbox - Host PC Windows 7 64). I'm not sure as to why they assigned address but no route at all.

Experiencing the same thing, on 3rd party routers, IPv6 will usually be kinda slow to access certain sites while it works great on the stock router provided by TM (mine is a D-Link DIR-615).

anyone on TM's ipv6 can access skmm.gov.my?

keep getting connection reset but works perfectly fine on ipv4

Yes, I can.

I am on Unifi IPv6.

See my ping to skmm.gov.my

i can ping the ipv6 address without issue but when i open the browser ( firefox / chrome ) it shows connection reset

Hi there!
i'm currently running OpenWRT BarrierBreaker final version on DIR-615.
i'm able to get ipv6 address for my wan interface starting with 2001:E68
however i'm not able to get ipv6 address starting with 2001:E68 for my lan.
does this mean that my place does not support ipv6 yet?
any help will be appreciated.
Thanks!

For Barrier Breaker, you use the subnet assigned to your PPPoE interface for the computers/smartphones connected in your LAN.

Hi there!
Thanks for the reply.
can you help to explain what steps are needed for configurations in Barrier Breaker?
i have tested with dir-615 stock firmware version 7.19 and confirmed that ipv6 is working on my area.
many thanks!