Really? guess I'll stick with my turbinemaster then.

OTOH I'm going to see if my newly acquired corsair AF 140 & AF 120 performed as it should be.

I bought two as from review, it says ' quiet ', and ' LDB ' Bearings, and i think, wow, shouldn't it last very long? and i bought it.

When i installed it at the top of my 690 III, wow... loud.... as it spins 2000 RPM all time. I remove the filter, and the noise lowered a little, so i changed back to CM Standard Case Fan 12cm.

hi guys want to ask..2 of my jetflo screws went missing..is it okay just to screw the fan in cross patten?thanks

No problem with it. If it vibrates, stuff small piece of paper beneath the unscrewed holes.

thanks bro

hi im planning to get yhe the corsair carbide spec 01... what case fan setup that will optimize the air flow to reduce the temperature?

Hi guys,

am new in the LED fan scene.. currently just bought a Tecware Alpha casing and thinking to change the 120mm fans in front of the casing to LED ones. can recommend me what kind of fan to use with white LED that look similar to Corsair Graphite 780t?

Prefer to be in low noise as i dont know how to control PWM fans with my current mobo & bad cable management skills.. haha

What fan is good 140mm ?
Cheap and goods

Corsair fan is good or noctua

hey guys,

I'm looking for decent case fan for my NZXT s340. I have a look around and there is so many brand and im not sure which to get.

I planning to add 2 new intake fan in the front and use back the original fan from the case on the top and back as exhaust fan.

Currently looking at corsair af140 which seem good and but a little but pricy at Rm90++ each?

Any recommendation?

U can try those san aces. they are PWM so can control fan speed via motherboard.

San aces

Are the fans in the master case 5 good?

Which fans should i swap it with, like 140mm with 3 pin?



I am using all 3 as the front intake and my existing jetflo 120 on the back ( for the fancy look ) hehe

This post has been edited by StuartLee2015: Aug 23 2016, 07:49 PM

I am also looking for 3 of these...

it's the Jetflo 140mm fan from the coolers..

anyone who don't use it and plan to sell it? I want .


Attached thumbnail(s)

There are always those corsairs af 140 LEDs one. Doubt anybody wants to sell their jetflo 140mm if any.

If u are looking for uniformity, change all to jetlfos

Yea... i like them too, but since the front can accommodate 140mm, normally i would use the biggest possible . And since the 140mm is the same as 120mm in terms of blade design, frame, and the bearing, they would last much better.


Currently using the stock fans 140mm ... hehe

i using jetflo 120 for the rear.

my case is Maker 5, changed from 690 III today.

This post has been edited by StuartLee2015: Aug 24 2016, 09:00 PM

Oh, so the mastercase got 2 140mm fans already. I think it is best to keep those 2 at front. For vertical position should last long time like the megaflow.

maybe can try WTB at garage sales? who knows u might get what u want.

I guess i will stick to the stock fans for now, i mounted 3x 140mm in the front. used the old jetflo 120 from my old case and monitor it's temp.

Looking at your specs I think it is enough to cool your rig with those fans.

Quick question guys, currently looking for a pair of 140mm HAF fans to replace the stock 140mm fans on my corsair h100i WC. Stock fans are just too noisy. Any suggestions? Thanks

Guys,
My casing is CM storm enforcer. Planning to change the stock 20cm front intake fan to either 20cm BITFENIX SPECTRE or 2 x 12cm BITFENIX SPECTRE. BITFENIX is a good brand or not? Based on the spec alone, the noise should be lower than 20dBA.

Can suggest best exhaust fan 12cm for top installation? Prefer silent and excellent air flow. Currently checking out Bitfenix Spectre or Silverstone FN121.
Please advise.

This post has been edited by DoomHammer: Nov 14 2016, 11:09 AM