Testing out these new fans from Noctua makes me realize just how much I like the innovative designs of their products. They do not simple take the ideas from others and make small improvements.They throw the book away and start from scratch.The Noctua Noctua NF-A12x15 may only be a fan, but I have never seen a fan where so much attention to detail has been made to every aspect of its design – airflow, noise, power consumption, aesthetics, accessories, durability and quality.With their static pressure are ideal fans for any CPU heatsink, radiator or all in one loop. In terms of noise our results spoke for themselves, they were absolutely outstanding and this is where the Noctua NF-A12x15 really shines the most.

http://www.xtremesystems.org/forums/showth...220#post5259220




Attached thumbnail(s)

Any recommend casing fan below RM50 ? Need some help

Hey guys, any good suggestion to replace stock fans that come with the Silverstone rvz01 case? Thanks.

hi guys,

anyone using Aigo RGB fans for their case? would like to know the feedback.

Thanks in advance

which is one is good and have long life expectancy

hey guys.. anyone knows of any good, strong and high cfm fan @ 5v?

need it for a project and it needs to run off powerbank.

Hello guys.
Pc noob here.

Looking to get an elite 130 case, it comes default with two fans. (main fan at front, one small fan at side)

However, the itx mobo I plan to get only has one case fan header. Is it safe to use a Y splitter?

Since it's a small case, would like to maximize air flow n cooling.

If I use the fan splitter, I'll have 4 fans (main, side, gpu fan and psu fan)

Thanks

Anyone here who use cm jetflo? Any thoughts on jetflo fans???

DELTA 120x120x38mm DC BRUSHLESS HIGH SPEED FAN
MODEL: FFB1212EHE
Specification:
Bearing Type : Ball Bearing
Rated Voltage : 12VDC
Operating Voltage : 5.0-13.2VDC
Rated Current : 3.0 Amp
Rated Input Power : 36 Watt
Max Speed : 4000 RPM at +12Vdc (Performance Mode)
Min Speed : 1980 RPM at +5Vdc (Silent Mode)
Max. Air Flow : 190CFM, 5.380m3/min
Max. Air Pressure : 17.78 mm H2O, 0.700 IN H2O
Max. Noise : 59.0 dB-A
Min. Noise : 26.0 dB-A

nislasteoh sell it HERE

thanks... i already have 4 of these... and not all of them can run at 5v (its a hit n miss).

plus at 5v, they are quite slow for what i need.


i dont mind finding 5v DC motors either as i can also slap some fan blades on them. thought about tamiya motors, but those are rated at 3v... scared they burn at 5v.

hi any1 know where can i get this thing?any seller here?


Attached thumbnail(s)

Bitfenix Spectre?got link who selling?

Hi, can recommend a good 140mm intake fans for my CM690III? currently I'm using the stock 200mm fan for intake and I feel it is not sufficient enough.

i got 8 fans..using Lian Li 011 casing..

but all use molex. so full power spin, and its quite loud.

its there any recomended fan controller for 9 fans?

You can try to use tweezer to press the connector pin's wing then push it out,
https://en.wikipedia.org/wiki/Molex_connector#Disk_drive
By default is 12V, if you change the pin location to 3 + 4 it will become 5V, 1 + 4 is 7V, just make sure the polarity is correct before power on.

This is easier than redo the connector that can connect to mobo fan header, those requires to buy specialized tool and JST pin + connector which normally only hardcore hobbyist does that.

erm...is there any device that can do all this?

There's no way to alter the voltage/amp of the AMP connector (not Molex, but both looks similar).
You can daisy chain all the fans together, then just switch the final connector wire position(1+4 or 3+4), you only have to do it once.

Blame Lianli with their stupid idea lol/

Guys,need help here.

I am using Cooler Master's casing, Masterbox MB511, pls advise which fan fits perfectly for better cooling purpose. Thks

Anyone can recommend some of the good and reliable case intake fans in the market now, budget ~RM50 per piece? NF-A12 is too expensive

scythe kaze flex