goldfries : hardly understand the prime you're running

what's your bios set vcore? i'll update later on

ehh. i'm just showing the results.txt file on the bottom left of the screen.

the success of priming is indicated by the time, so as you can see the time will indicate that i did 8hr+ of priming.

BIOS set vcore? i stated mah VOLTAGE APPLIED: 1.500V

not that one ah?

didn't saw

i wonder where's jslut....

CPU: AMD Sempron 3000+ (32-Bit)
STEPPING: dunno... lazy... will update later when change to XP-90
SPEED: 2590 (370 X7)
VOLTAGE APPLIED: 1.50V
COOLING: AIR

MOTHERBOARD: MSI K8N Neo3-F (nforce 4-4x)
RAM: 512MB X 2 Hynix DT-D43 (double sided)
DIVIDER: CPU/11 (133FSB Setting)
RAM TIMING: 3-4-4-8 2T
RAM VOLTAGE: 2.8V

POWER SUPPLY: Chapalang China 400W
CPU COOLER: Stock Sempron64 2500+ cooler @ 3000 RPM







This post has been edited by briangan: Feb 19 2006, 07:33 PM

CPU: AMD Sempron64 2800+ @ 2.4GHz (300.4 X 8) 1.5v
0527UPMW
MoBo:Abit NF8
Memory: 512MB KINGSTON VALUE RAM PC3200
TIMING: 3-3-3-8 (CL-RCD-RP-RAS) 1T
Memory speed: 200.3 MHz 2.8V
Video card: nVIDIA GeForce 6200 AGP
PSU: ACBEL IPOWER 400W
CPU COOLER: Thermaltake silent boost wit modded 120mm nmb fan (1200rpm) ->by AllnGap

CPU: AMD Sempron 2800+
STEPPING: LBBWE 0527 UPMW
SPEED: 2656MHz (332MHz x 8)
VOLTAGE APPLIED: 1.61V
COOLING: AIR

MOTHERBOARD: DFI LANParty UT nF3 250Gb
RAM: 1Gbx1 Infenion BE-6
DIVIDER: 3/2
RAM TIMING: 3-3-2-8 @ 1T
RAM VOLTAGE: 2.8V

POWER SUPPLY: Enermax Liberty 500W
CPU COOLER: Scythe Ninja plus

This post has been edited by sidewinderz: Mar 20 2006, 06:20 PM


Attached thumbnail(s)

my sempron 2800+, revision is DH-E6, but then what is mean by DH-E6?

means that yours is revision E6....

Revision of E6 is good or not? i mean in terms of OC... becoz most ppl whose sempron is E6 can highly OC of it...

you already answered yourself

soulfly, where is da cpu-z and prime for superpc's Sempron 2500+ E6?? i can only find his Sempron 2800+.. plz update.. tQ..

i think screenie image link dead already... pic is not displaying

ic.. can update mine..??

CPU: AMD Sempron64 2500+ @ 2.24GHz (320.1 X 7) 1.45V
Stepping : hard to remove waterblock..
Motherboard : DFI LANPARTY UT nF3 250Gb
Memory: 1024MB OCZ OCZ4001024DCGE-K Dual-Channel PC3200 SDRAM
TIMING: 2.5-3-2-5 (CL-RCD-RP-RAS) 1T
Memory speed: 186.7MHz DDR373 2.8V
Video card: ATi Radeon 9600XT AGP
PSU: ACBEL IPOWER 450W
CPU COOLER: Cooler Master Aquagate Mini R120 Water-Cooling



This post has been edited by termignoni: Jul 17 2006, 04:29 AM

how come watercooling only 2.24ghz? that's low man....

i know.. bootable at 2310 (330x7) but only for like 5secs.. still trying though, need to learn somemore.. any sifus here care to guide..?

This post has been edited by termignoni: Jul 16 2006, 07:39 PM

I'm not really familiar with your RAM characteristic.... what is it originally rated at?

Anyway...try this....

DRAM Frequency Set - 150 (DRAM/FSB:3/04)

Command Per Clock (CPC) - Enable
CAS Latency Control (Tcl) - 2.5
RAS# to CAS# delay (Trcd) - 03 Bus Clocks
Min RAS# active time (Tras) - 07 Bus Clocks
Row precharge time (Trp) - 03 Bus Clocks
Row Cycle time (Trc) - AUTO
Row refresh cyc time (Trfc) - AUTO
Row to Row delay (Trrd) - AUTO
Write recovery time (Twr) - AUTO
Write to Read delay (Twtr) - AUTO
Read to Write delay (Trwt) - AUTO
Refresh Period (Tref) - AUTO
Write CAS Latency (Twcl) - AUTO
DRAM Bank Interleave - Enabled

DQS Skew Control - Auto
DQS Skew Value - 0
DRAM Drive Strength - AUTO
Max Async Latency - 8.0 Nano Seconds
Read Preamble Time - 6.0 Nano Seconds
IdleCycle Limit - 016 Cycles
Dynamic Counter - Disable
R/W Queue Bypass - AUTO
Bypass Max - AUTO
32 Byte Granularity - Disable

LDT multi = 2.5x

thx bro.. will try tonite.. da stock @200MHz is 2-3-3-7..

if cannot use 150 divider, use 133

tried this setting with my 2x512mb KVR (unknown whhat chip and cant check coz of heatspreaders...also rams bought at different times and diff places... so i guess the chips must be diff)

cant get muh fsb past 250x9.... its bootable...and useable...but not prime stable... run 1 second got error already if run cpu stress test.

but if run blend test cpu+ram its ok...

also tried dram frequency 133.... sigh

highest ive ever gotten is 252x9 with dram at 100 and the rest auto... cant run prime...but can run 3dmark 03 05 06.

rig specs:

~ A64 2800+ s754 (XP-120 w/ Delta FFB)
~ DFI LanParty NF3 250Gb (forgot bios version....its the one with the built in memtest and the friggin high dram voltage by jess1313)
~ 2 x 512MB KVR (dunno what chip as explained above)
~ Asus V9999/TD 6800 (Zalman Fatal1ty)
~ WD 320GB SATA HDD (plugged to sata 3)
~ Cooler Master 450-ACLX PSU

This post has been edited by mADmAN: Jul 21 2006, 02:06 PM

8 hours prime? Thats ridiculous. Why need 8 hours, to prove PC is stable?