This time with 3770K.... hyper & PSC chips

Corsair DomGT 2000C7 @ 2400 8-8-8-25-1T


G.Skill RipX 2200C7 @ 2500 7-11-7-28-1T


* efficiency is not there anyway

I'm not a pro in Pi benching so need some advice from Pi kaki to optimize the score


That was painful to watch, scared of blood LOL
Added to latest news & update section in the top post.
Thanks for sharing bro.

ambient: 33C

SuperPi is a single threaded program so it's not stressing all cores.
HyperPi is the multi threaded app in which my bad chip will not be able to survive due to sky high temp even @ 1.55C

I actually uploaded the wrong ss LOL.
Nvm add 3C to the first core. The rest should stay intact. I'm using custom wc without TEC, coz the acrylic top leaked & waiting for replacement before this single TEC is up for resale later. Then i will be using the Quad TEC + dual controller.

Team Xtreem 2600C10 @ 2666 10-12-12-25-1T


This post has been edited by owikh84: May 22 2012, 07:08 AM

Well done bro. Basically you could OC any RAM with IB due to strong IMC integrated on die.

I still cant break 6m30s barrier at 5.0GHz.
Wazza checked
TinyXP 32/64bit checked
Large Sys Cache checked
Priority & Core affinity checked
Silver theme checked

Maxmem pending
Tighter TRFC pending
Lower LB pending

If it's a good kit you should be able to push it to 2000 9-10-9-24-1T @ 1.65v

Google for Vengeance 1600 to 2000 to find out more details

Managed to shave up 6s with MicroXP 0.86

Playing with BCLK OC

3770K @ 5.0GHz = 104.2 x 48 | 2780 10-12-12-21


3770K @ 5.0GHz = 106.4 x 47 | 2766 10-12-12-21


sub 28s latency
3770K @ 5.0GHz | 2666 9-12-12-21

3770K @ 5.0GHz = 104.2 x 48 | 2777 10-12-12-21-1T

1.87v, 1.25v, 1.2v
Didnt really monitor the core temps at this vcore but this 3770K is able to run 32m at 5.0GHz with 1.48v mac 82c.

Yeah that's under water.
Heat dissipation inside IB is damn poor due to bad TIM paste used.
I haven't run any 3D benchmark on 5GHz yet until now.
If everything's ok i will put it on my incoming Quad TEC + dual controller next week.

For sure dual core wont need that much.
don't want BSOD when taking SS just in case of bad luck so let it be LOL.
yupe those timings can still be tighten, later.. later bro

well i will take it as a challenge.
Still a lot of ram tweaks need to learn in MVG BIOS.
The latency boundary, tRRD, tFAW, tRTP is not the best yet.

start hunting for a golden 3770K bro
Nice clocks man!

I'm on subzero for the first time.

Quad TEC + 2x RX360 + 12x GT + EK X2 250 Adv + EK FC7970 + D5 + EK top + XSPC white tubing


Quad TEC + Dual controller:


3770K @ stock


idle:


load:


This post has been edited by owikh84: Jun 9 2012, 10:22 PM

No worries on condensation as both the mobo + TEC block are insulated properly with Kneaded Art Eraser.

This Quad TEC is works insanely great as per descriptions in the original OCN thread.
I still got an extra TEC, the single TEC but haven't tested the replacement top which was cracked previously.

My SB-E rig doesn't really need more than an AX1200 for stock trifire 7970 + OCed 3930K.
AX1200 can pull more than 1200w out of specs.
Quad CF needs 2 of these PSUs.

CPU socket + backplate + TEC block are the ones tend to condense when going extreme cooling like this.
Not the mosfet VRM part when it comes to CPU-only cooling.

---

Added on June 9, 2012, 10:51 pmI will sell the single TEC after testing ok. But you need a low room humidity to make it worked = airconded.
The TEC block without controller power performs badly for sure.



This post has been edited by owikh84: Jun 9 2012, 10:51 PM

Good for you. yes i have the single controller in the first page of this thread.
I need to do a leak test first before putting this up for sale though & it won't be cheap.