EDIT: 1600Mhz 8GB Ram. Going to get 4 of them. Thanks.
if can OC, then will try to OC 
This post has been edited by eugenelimys: Dec 25 2012, 04:37 AM
[Official] LYN DDR3 Discussion Thread, Show or Learn To Overclock Your DDR3!!
|
|
 Dec 25 2012, 04:35 AM
|
 
Senior Member
639 posts Joined: Dec 2010 From: Nowhere; Anywhere; Somewhere  
|
New here. Going to buy AW M17x soon. Was searching for 8GB laptop ram. Which one is good? Can OC? (Still new, don't really understand a thing after reading)
EDIT: 1600Mhz 8GB Ram. Going to get 4 of them. Thanks. if can OC, then will try to OC This post has been edited by eugenelimys: Dec 25 2012, 04:37 AM |
Quote|
|
|
|
|
Jan 5 2013, 02:15 PM
|
Junior Member
345 posts Joined: Jun 2009
|
nak tanya otai ram ni best tak oc
Attached thumbnail(s) 
|
|
|
Jan 6 2013, 01:03 PM
|
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4 
|
QUOTE(keyo @ Jan 5 2013, 02:15 PM) nak tanya otai ram ni best tak oc how about you try OC them then share the result here   i personally never tried any qimonda chip before. |
|
|
Jan 6 2013, 01:21 PM
|
 
Elite
8,711 posts Joined: Nov 2007 From: Butterworth, PG / Machang, Kelantan
|
Currently there are a few ICs that are great at OC.
1) Samsung HCH9 & HYKO 2) Hynix BFR & CFR 3) PSC 4) Elpida BBSE The rests are bad or just okay. |
|
|
Jan 6 2013, 10:45 PM
|
|
Junior Member
345 posts Joined: Jun 2009
|
Not buy yet tq
 This post has been edited by keyo: Jan 6 2013, 10:47 PM |
|
|
Jan 9 2013, 11:46 PM
|
|
Junior Member
345 posts Joined: Jun 2009
|
buy this ram rm 50 d9kpt ,can i know how far this ram can go,is it ok not using heat sprader using voltage 1.6v tq
Attached thumbnail(s) 
|
|
|
|
|
|
Jan 11 2013, 10:04 PM
|
|
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4
|
QUOTE(keyo @ Jan 9 2013, 11:46 PM) buy this ram rm 50 d9kpt ,can i know how far this ram can go,is it ok not using heat sprader using voltage 1.6v tq some info regarding this chipQUOTE average D9KPT/KPV clocks same as handpicked D9JNL/JNM 1600 7-7-7 : 1.70-1.75V for KPT , 1.75-1.80V for JNL 1800 7-7-7 : 1.85-1.90V for KPT , 1.90-2.00V for JNL 1800 8-8-8 : 1.70-1.75V for KPT , 1.75-1.80V for JNL 2000 8-8-8 : 1.90 for KPT , 1.95-2.00V for JNL 2000 9-9-9 : 1.70-1.75V for KPT , 1.85V for JNL link : D9KPT @OCXtreme.org btw you can go up to 1.65V which is very safe. for benching, some people dare to go up to 1.9V (if the chip didn't give up yet) but for me, 1.8V is my redline --> depends on voltage scaling for the chip. This post has been edited by lengchai86: Jan 11 2013, 10:06 PM |
|
|
Jan 12 2013, 11:53 AM
|
Senior Member
1,457 posts Joined: Jul 2009
|
Sifu, I bought Kingston Hyperx Genesis KHX1600C9D3K2/8GX and I try to search for the IC they used but couldn't find it.. Any idea?
|
|
|
Jan 12 2013, 07:22 PM
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
Check your packing...........
02 or ELP = Elpida 08 = Micron 16 = Samsung 32 = Hynix KTC = Powerchip / PSC 16 = Samsung:  This post has been edited by stasio: Jan 13 2013, 07:14 PM |
|
|
Jan 13 2013, 05:13 PM
|
|
Senior Member
1,457 posts Joined: Jul 2009
|
QUOTE(stasio @ Jan 12 2013, 07:22 PM) Check your packing........... 02 or ELP = Elpida 08 = Micron 16 = Samsung 32 = Hynix KTC = Powerchip / PSC 16 = Samsung:  Mine is 12  Then is which 1... haha...This post has been edited by t3n: Jan 13 2013, 05:14 PM |
|
|
Jan 13 2013, 07:05 PM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
QUOTE(t3n @ Jan 13 2013, 05:13 PM) Mine is 12 http://www.xbitlabs.com/articles/memory/di...r3-2x4gb_7.html Then is which 1... haha...This post has been edited by stasio: Jan 13 2013, 07:14 PM |
|
|
Jan 13 2013, 07:17 PM
|
|
Senior Member
1,457 posts Joined: Jul 2009
|
Micron D9PFJ
Thanks bro..!! |
|
|
Jan 13 2013, 11:10 PM
|
|
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4
|
QUOTE(t3n @ Jan 13 2013, 07:17 PM) Micron D9PFJ more PFJ HERE Thanks bro..!! This post has been edited by lengchai86: Jan 14 2013, 02:57 PM |
|
|
|
|
|
Mar 24 2013, 11:32 AM
|
|
Junior Member
345 posts Joined: Jun 2009
|
QUOTE(t3n @ Jan 13 2013, 05:13 PM) Mine is 12 Then is which 1... haha...This post has been edited by keyo: Mar 24 2013, 11:34 AM Attached thumbnail(s) 
|
|
|
Mar 29 2013, 01:22 PM
|
Senior Member
4,667 posts Joined: Jan 2005 From: UniVeRSiTy Of MaLaYa 
|
quick run on Samsung Green 8GB kit, 2400Mhz stock timing
 
|
|
|
Mar 29 2013, 01:58 PM
|
 
VIP
15,903 posts Joined: Jan 2003 From: Miri 
|
QUOTE(bulibulizaimon @ Mar 29 2013, 01:22 PM) quick run on Samsung Green 8GB kit, 2400Mhz stock timing which batch do you have? my YK0 1205 does 2133 10-11-10-30-1T at 1.325V ... currently limited by Sandy mem controller limitation, can't go beyond 2133 divider.
|
|
|
Mar 29 2013, 04:40 PM
|
|
Senior Member
4,667 posts Joined: Jan 2005 From: UniVeRSiTy Of MaLaYa
|
QUOTE(soulfly @ Mar 29 2013, 01:58 PM) which batch do you have? my YK0 1205 does 2133 10-11-10-30-1T at 1.325V ... currently limited by Sandy mem controller limitation, can't go beyond 2133 divider. YK0 1240 batch.. LinX stable 2400Mhz @ 10-11-10-28-1T using 1.45Vmy RAM can't go beyond 2400Mhz even with 1.7V  or maybe need more tweak  This post has been edited by bulibulizaimon: Mar 29 2013, 04:41 PM |
|
|
Mar 29 2013, 10:05 PM
|
|
VIP
15,903 posts Joined: Jan 2003 From: Miri
|
QUOTE(bulibulizaimon @ Mar 29 2013, 04:40 PM) YK0 1240 batch.. LinX stable 2400Mhz @ 10-11-10-28-1T using 1.45V try loose the timing a bit ... maybe 11-11-11-30-1T or somethingmy RAM can't go beyond 2400Mhz even with 1.7V or maybe need more tweak |
|
|
Mar 29 2013, 10:47 PM
|
|
Senior Member
4,667 posts Joined: Jan 2005 From: UniVeRSiTy Of MaLaYa
|
QUOTE(soulfly @ Mar 29 2013, 10:05 PM) try loose the timing a bit ... maybe 11-11-11-30-1T or something hit the speed wall already i think.. PC wont boot even after loosen to 14-14-14-36 @ 1.75V |
|
|
Apr 3 2013, 11:56 PM
|
Senior Member
8,686 posts Joined: Mar 2009
|
|
| Change to: |  0.1113sec
 0.84
 6 queries
 GZIP Disabled
Time is now: 30th November 2025 - 10:20 PM |
All Rights Reserved © 2002- 2025 Vijandren Ramadass (~unite against racism~)
Powered by Invision Power Board © 2025 IPS, Inc.