try lian li ex-33 very good.......... i just bought 1 and install.....

look nice for me .........come with fan filter too n best of all, the hdd can be lifted out anytime


This post has been edited by LExus65: Jun 26 2007, 09:40 PM

where u got those fan holder for the Vizo Starlet (below the Lian Li EX-33)

what's that? what brand?

This post has been edited by E-J@1: Jun 27 2007, 03:14 AM

whoaaa a lian-li stacker very nice, i'll check it out bro



i think that came from the stacker's fan frame (the 4 fan door thingy). you can dismantle the brackets and install em on the front bay

LExus65, looking good with the lian li harddisk kit!! wanna ask u something,how easy is it to remove the fan filter from the kit?

nice nice

but i m trying to use all CM tngs i can in my stacker ler

the EX-33 fan filter is totally just slot in (or i said drop in) separated from the fan assembly, and everything is screw on.........no problem, installation is easy too just push in and screw it........much much better then the CM 1.........CM should learn it

the other fan holder is from the side 1, my HR-01 is too tall already blocking one of the filter so have to remove it, but i found a good use in the front haha.......

so far only problem with the EX-33 is stick out a bit front and back, and the fan filter is attach to the front bezel, so if u remove it then no more filter u have to use back the CM ori cover to hide it

i'll load some picture later on, being busy this few days at work, not much time to play around yet

die hard CM fans........... too bad not all CM stuff are good though a bit dissapointed

This post has been edited by LExus65: Jun 28 2007, 11:19 AM

thanks to ryo now my hdd up n running where it should be hehe , and some snap on my rig XD









>,< not sure howto enlarge it 1st timer on this soz ;Þ

*bonk lexus65*

This post has been edited by onenique: Jun 28 2007, 01:45 PM

wah very nice, but brother can make the picture a bit larger.......very hard to see hehe

edited, thank you thank you, now can very very clearly now

This post has been edited by LExus65: Jun 28 2007, 07:05 PM

mod: wondering if u guys know how to get the side panel (transparent ones) for stacker :3

enlarged pics lexus any tips on how to hide the spider webs ^^?(cablesss pls) :Þ

OMG the wires dude. Time to do sum wire management man. Looks like a jungle in there. Also noticed u haf the 8800GTX slotted into the PCIe 8X slot. U shud be using the topmost slot for single card use IIRC.




Here's 1 I just did.



This post has been edited by ianho: Jun 28 2007, 04:17 PM

wah ... that's so clean, did u cut out the original mesh and stick an acyrlic on it ??

It looks like comes in default ...

@onenique

Do u honestly need that many fans inside of the case exhausting air ???

Actually with ur setup, just put one fan on the top and one at the bottom bracket of the side fan slot to blow ur gc and CPU already good enough...

oh u sure ^^?; i read it sumwhere in the forum it says its best to slot the card in the middle (for single card) ... gotta recheck on that >,< thanks for the IIRC info btw
*i know headache to see the wires lols


wooo~very nice work ..very smooth~ where u @ ianho ? could u pm me on how much ur charging for both panels ?

thanks ²c²v

When I looked around the web for Stacker window mods, they all look so ugly. All of them take off the mesh n use screws to mount the window. Even the rm3500 custom Stacker by Smooth Creations is using that ugly window mod. U can c the holes that r used to hold the mesh to the panel around the window. So I designed my own mod n came out with a clean look where u dont c the ugly holes around the window frame.

That's the big question how did u mount the window ???

It doesn't looks like there's any sign of double tape of screw ...or whatsoever ..

it just so clean ...

I'm thinking to continue my mod of the side panel and still wondering how to mount the side panel .. coz I might not able to mount the side panel with long bolt and nut coz the side patent fan would blocked it from sliding back properly ...

I've cut a big square and sand the edges but no idea how to mount the acrylic piece as clean as possible without using fuzzy double tape or screw mount..

Plz here me ....

i taught onli i hving a tropical rainforest ~~

finally can show off ur raptor ed gratz


@Doom

interested on ur exat

ur right, middle slot is 8x /bump thanks again >,< if i ever need the nice side panel ur modding definately will pm u
; ; ; its super hot inside there ... no air con in the room + smoke heavily in closed room (wife pregnant cant leave the door open) = dead hot chilli paper

hahah thanks man , wanna come join lepak in the rainforest ^^?

hahha temporary reserved for someone else ... until this saturday ,,

Anyway back to the topic ...

The stacker is really lovely case ... too bad it's just too heavy for me to lift.

uncle turn that cmstacker transparent side panel upside down just to make sure it didnt fall over hehe

i tot ur thermal take tough power is a modular PSU, how come u end up with still so many wires ?? but it really looks impressive.

get a rounded ide cable, and some wire tie strip.........

uncle's mod really nice........wander if CM would buy your patent or not......

you're most welcome man, glad to see that that sexy raptor is putting the HDD bracket in good use
and yea, tidy up your wires bro, jungle fever!

This post has been edited by Ryo: Jun 28 2007, 07:40 PM