thanks to professorie Chuah

actually i found this MDMA beta 10 accidently because i am looking for icon 505 firmware and dashboard to flash,.. still failed to flash and giving me error code 102

and in the same time i found this, totally so rocking good news and solve my Maxis Stuck at 3G problems.

now i can connect to HSPA directly without worry it stuck at 3G again,....

by the way , your speed very amazing digilife,.. seems like your E1762 is back and alive,... or u using ZTE MF691 ??

hope Fruitie can pin this MDMA beto 10 thingy on first pages,..

This post has been edited by chuahcs79: Dec 18 2011, 09:18 AM

tat was MF691 on maxis

now E1762 on umobile



umobile here hav 2 towers, 179xx and 179xx, both weild same results but maxis here hav umts900+umts2100 towers 492xx and 135xx one is good on upload and one is good on download, pick your choose via the NEWLY discovered MDMA



This post has been edited by digilife: Dec 18 2011, 09:31 AM

Thanks for that and I have to think of a way to put up on the first page.

I want to try that but as you know my direct plug-in sucks plus I can't use my router anymore. Lack of USB port...

---

Added on December 18, 2011, 10:33 amEarly in the morning's speed:


Still on the same IP address...

---

Added on December 18, 2011, 10:49 amAnyway, just wanna try out this MDMA stuffs, haven't tried before.

So, what I did was, I tried running this MDMA and when I clicked on "connect" tab, it shows this error:

---

Added on December 18, 2011, 10:51 am*Ignore the "Initializing mobile data device..." I did try to click when it was on "Ready" status and the error showed up.

---

Added on December 18, 2011, 11:13 amAnyway, managed to Google Error 623 and I don't understand how to copy a created RAS profile from my current dashboard. Chuah, care to shed some lights on me?

New IP address.


Oh, how I miss you >6Mbps.




Sure later approaching evening, the speed will drop to 1Mbps...





This post has been edited by fruitie: Dec 18 2011, 11:13 AM

me 2, having the same prob as Fruitie

now the new MDMA cannot connect the usual way

go to "open network and sharing center" >"change adaptor settings"> look for "Wireless Broadband Connection" ~ "LAN or High Speed Internet" > right click to connect,

once you are connected, you can see the new MDMA button also show "connected" take note of your Tower Code and note them down which is UMTS900 or UMTS2100

------ot-------


anyone here using Celcom SKMM pack as a backup?

only rm25/mth

my best effort as below when downloading






if use VPN can go truely unlimited as claim by some users,

This post has been edited by digilife: Dec 18 2011, 05:31 PM

im using it too, 1.5mbps constant at my place, universiti malaya..

bro, care to explain the vpn thingy? interested..

------------OT again-----------

mine only once or twice touch 1.5Mbps, wat is your RSSI over there

the VPN thingy u hav to google as i only hearsay from forum

sorry ya off topic, lets talk in pm la digilife..

how to determine whether it is UMTS900 or UMTS2100? if HSDPA/HSUPA means UMTS2100? tower code is which column?

fruitie,

u can try to use window 7 mobile broadband to connect your E1762 via direct plug in,

below as some method are using NDIS instead of using MDMA beta 10 RAS,... that works, after window 7 auto connect, then u can open the MDMA beta 10 to choose which band tower to get better speed at night


download E1762 driver from HERE

first, remove your maxis/mobile partner dashboard/dialer u install,

replug in your E1762, and wait for cwin 7 to recognise your E1762 first ,

then launch the driver Setup in E1762 driver u download,.. ( unzip the rar file of E1762 driver u download,. and go to huawei driver then driver setup,. , double click and launch the installer,.. )

this will make your pc recognize your E1762 without instal those maxis or mobile partner dashboard, and direct using the window mobile broadband dialer and st APN and just connect straight,.. )


aboev method get me the highest speed ever and most consistent and also window will use NDIS ethernet emulation to dial your E1762 under Local Area Connection,..

when i use my E1762 with my router, speed very very poor, UL speed decrease ,.. only get 1.2Mbps max and DL speed only 4~4.8Mbps,..Ping is between 70~95ms,..


but when i use method above, i get 6~6.8Mbps DL and UL get 2~3.6Mbps,.. PING is good around 45~65ms,.

---

Added on December 18, 2011, 6:17 pmu see the Band config, click it and select which band u want to use, after u click ok you will see the Cell ID ( tower code ) change ,.. signal will be different,.

This post has been edited by chuahcs79: Dec 18 2011, 06:18 PM

i am still using UMTS 900Mhz 3G band,signal still going strong and never dc at all for last 12 hour plus

[attachmentid=2592154]

If anyone of you always stuck at 3G 384Kbps, then u need to change to 900Mhz 3G band to use,.. as 3G ( 384Kbps ) is 2100Mhz 3G band too,.. so sometimes when u select 2100Mhz u still end up get 3G tower instead of HSPA tower,..

---

Added on December 18, 2011, 6:53 pmE1762 direct plug on UMTS 900Mhz 3G band


finally something i am happy and satisfy,.

This post has been edited by chuahcs79: Dec 18 2011, 07:09 PM

Wah, Chuah, that's a long process to get it done! Let me digest it when I'm free.

Meanwhile, I just got back from outside. Was loitering around PJ and Subang area.

Still on the same IP address.







Looks good for now as recently I don't get this kind of speed even at these hours. Not sure if it is solved or not. I wasn't around to try out just now.

well, when i select UMTS 2100Mhz and get a HSPA signal,. DL speed is much higher but UL speed is low,.


on 2100Mhz DL speed is good, but UL is low and cause bad ping



after discover this MDMA beta 10, my E1762 can stay on the 3G band i prefer and even on router speed is very good, if i need to upload something, i will select 900Mhz, if i want to DL, i select 2100Mhz,.. oh well

---

Added on December 19, 2011, 2:38 amswitch back to 2100Mhz HSPA tower now

[attachmentid=2593010]

This post has been edited by chuahcs79: Dec 19 2011, 02:39 AM

Speed is still good on 2100Mhz 3G band HSPA signal,



[attachmentid=2593749]

Good speed is back.


For a while only... But still OK la...


Looks good for now.






Much better compared to last week, glad that Maxis did improve for at least one night...

---

Added on December 19, 2011, 10:12 pmMy speed is back.

I'm downloading more than 1MBps now.

This post has been edited by fruitie: Dec 19 2011, 10:12 PM

LOL, am sure u connected to 2100Mhz band HSPA tower,. somehow that tower is down,.. and guess after u report maxis is fixing it and now back to normal,.

congrats fruitie, miss your 6Mbps very much le

For me, the best is using nokia x3-02 ( because it can connect to 2100Mhz HSPA tower instead of stuck at 2100MHZ 3G tower like my E1762 )

Of course, imagine watching Youtube videos with buffering? Something which I have never experienced for long time. More than 6Mbps speed.



Next thing that they will do is on the FB vids and upload issues, the technical guy who called me said they are well-aware and trying their level best to get these issues solved.

This post has been edited by fruitie: Dec 19 2011, 11:03 PM

i think maxis have quite the best service team compare to other telco... oh well, if the speed is consistent, then youtube confirm no buffer, if buffer = dial up ages,.. LOL