Remember to standby some Panadol ActiveFast when you do it.

By the view of it, it shouldn't be that difficult but I'll prefer to hand over to someone pro in this area to do it.

If I were to do it, I must be prepared with some hiccups.

Remember the first time you setup the HW550 ?



Wat time you finally have time to go mandi ?




btw, i found out that HW550 ROCKS, sell me yours can ?

That time the fault wasn't on the router but iPad.
Anyway, why do you want it?
It can't recognize supercharged E372 anymore.

that time was offering him helping him flashing openwrt Via Teamviewer with USB modem direct plug usb port,.

lol, you want Openwrt ?

i though u happy with stock firmware

This post has been edited by chuahcs79: Nov 11 2012, 07:45 PM

Remember the first time when you bought the HW550 and tried to setup to match it with your MF622 ?

This Router if you match it with a MF680, dismantle the Antenna , disable WiFi can give you very low ping.

My Mr3420 V1 and V2 cannot match it at all on ping.

Moreover, i discover that without using WiFi, the router is not hot and does not requires a Fan to blow it.

I open up , as shown in my earlier posting, the inside was nicely spaced out, no cramped circuits, capacitor also good quality.

I even re-enabled back wifi without putting back the Antenna, it too work great.

Now the next step is to get a DDWRT flashed router and LAN out from HW550, you can have very good WiFi in your place.

I just missed the chance to buy a used Linksys DDWRT flashed router for only rm60

Yes, that time bought for iPad. It was iPad's fault.

speed with TL-MR3420 STock firmware

[attachmentid=3150752]

How you managed to overcome it?

Channel conflict?

Just reset network settings on iPad.

Chuah, why OpenWRT no fun ah? use back stock FW


I dare u to flash to DDWRT

I sponsor you Activefast

DD-WRT bugged 3G support

nope, sorry NO-> DDWRT, it is very suicide and iddott move for beginner,

As most people know DDWRT = no failsafe,..

why not you try ?

i dun need to flash

i just need a missing link, a DDWRT flashed router.

my HW550 can supply the broadband connection via LAN out from HW550 into the WAN port of the DDWRT router

i just mentioned much earlier on, i missed the chance to buy a used Linksys , its DDWRT Flashed , rm60 je

well i am just trying to prove a point :

u are using Cat6 cable + stock firmware


so i am using Cat5e ( 7.5meter ) + TL_MR3420 V1 stock firmware + ZTE MF680

result :

no spikes in speedtest,.
[attachmentid=3150769]

Ping Test :
[attachmentid=3150771]

This post has been edited by chuahcs79: Nov 11 2012, 08:26 PM

thx.. yea. im using maxis.. so what i should do is call maxis to give public IP ? and using this router for successful port forwarding ?

no fight la Chuah,

Your RSSI = -55, mine RSSI = -93d

How to compare, like the canto sayings goes "to compare a Mosquitoe with a Cow".

You are like Manchester United FC and I am like Liverpool FC

Btw, you reverted back to stock firmware before i brought out the Cat6e cable to discuss, why you dun like OpenWRT ?

why dont u do a test like me with your so called Cat6 or Cat6e cable ?

oh the stock firmware i flash it back to prove a point to you ma, ia m pro in flashing, now it is back to openwrt

This post has been edited by chuahcs79: Nov 11 2012, 08:38 PM

no point to argue with you , i cannot challenge you as your area have far much better signal than me, but i can say that even though my signal sucks compared to yours, i can get better ping with a cat6e cable on sucky signal.

I dun lie, its in my screenshots, ping of 27, can you touch so low with wat ever patpou that you have over there coupled with RSSI of 55~65, E372,Mf680, OpenWRT, Antenna, Cooler pad, fan, Naked modem, 5 Towers in front of your window ?

I am trying to prove that without all those in my area, i still managed to get Ping of 27, why?

Just 3 basic things, HW550,MF680 and Cat6e Cable on the RSSI of 93 and Low Signal

Hey where did you get your CAT6e cable?

My Cat5e kena cat bite