oh hitachi.. also quite good, but not many dealers around.. repairing and part might be difficult..

just get the diamond cutter cut 2 lines and use rotary hammer's chisel and chisel the inbetween part lo then lay conduit or cables and cement back..

why need angle grinder ?

unless u want to use this method to wallchase la



not sure where u can get those type of head to cut

is really wan wall chaser can get this




---


or you can just use rotary hammer's impact mode and buy a channeling chisel...

refer few pages back i think pg 2 or 3, it was discussed

This post has been edited by JinXXX: Mar 2 2012, 11:21 PM

If job are small, just use diamond cutter + rotary will do.

My alarm wireman friend don't need to use rotary hammer, just use diamond cutter make one deep hole, conceal the wire and seal the opening. Diamond cutter is fast.

I got diamond cutter, and also cement grinder.

cement grinder ???

jinxx still can find any channel chisel for sale like armeg in local shop le.

the 2nd video i found einhell do have for sale in malaysia but the width capacity is only 26mm, aircond sure need to cut bigger than this rite.

weikee what is cement grinder? tyty

---

Added on March 2, 2012, 11:44 pmtypo, cant find locally*

This post has been edited by Eng_Tat: Mar 2 2012, 11:44 PM

i think its also called polisher.. cement polisher ...

so you can get surfaces like these


more info > http://en.wikipedia.org/wiki/Polished_concrete

That is concrete polisher I got also is like sand paper got difference grade.

The one I mention is like below link.

http://xmverich.en.made-in-china.com/produ...ding-Wheel.html

how do you keep it "flat" , when your polishing..

/sense derailment on the way/

what do you all think about dewalt brand? relliable or not as their diamond cutter is the cheapest rm250 only bosch and hitachi rm300++

Makita Rotary Hammer/ Combination Hammer with AVT
HR2611FT - comes with Quick Change Drill Chuck

• Anti-Vibration Technology (AVT) actively counteracts vibration of tool for greatly reduced transmission to operator
• Torque Limiter stops bit rotation if bit jams for increased operator safety and enhanced tool protection
• High Durability design with Zig-Zag Armature Varnish, Enhanced Sealing, Improved Impact Bolt and Impact Reducing Cushion Ring
• Reverse Rotation System using Brush Holder Unit provides the same amount of power in forward and reverse and extends life of carbon brushes
• Improved Bit Guide for increased bit stability during drilling applications
• Re-Located Operating Mode Lever for increased protection and durability
• Variable Speed Trigger allows operator to adjust speed based on materials or application
• 40 Angle Bit Positions enable chisels to be positioned at optimum angle of operation
• One-Touch Sliding Chuck for easy bit installation and removal
• LED Job Light illuminates work area
• Ergonomic Soft Rubber Grip for vibration absorption and comfortable operation

Bit Type : SDS-PLUS

Capacities:
Concrete : 26 mm
Core Bit : 68mm
Diamond core bit (dry type) : 80mm
Steel : 13 mm
Wood : 32 mm

No Load Speed : 0 - 1,200 RPM
Blows Per Minute : 0 - 4,600 BPM
Impact Energy : 2.9 J (2.1 ft. lbs.)
Vibration Level : 10.5 m/s2
Noise Level : 90 dB
Overall Length (with SDS-PLUS Chuck) : 385 mm
Net Weight : 3.0 kg


AVT Techonology demonstration & introduction


This post has been edited by jeffreylam: Mar 12 2012, 02:29 PM

jeffrey, it would be best if you can put the price together as info. thanks

Eng_Tat : Whats your location, good news Makita will have roadshow in Kluang, Johor next month.

This post has been edited by jeffreylam: Mar 12 2012, 02:31 PM

Jeff i am in jb, any road show around here? also where can i get pricelist for makita products? you help is greatly appreciated

---

Added on March 12, 2012, 2:41 pmalso what is the date of roadshow in kluang? thanks

This post has been edited by Eng_Tat: Mar 12 2012, 02:41 PM

Makita Authorised Service Sentre

One Stop Machinery Services Sdn Bhd
7701, Jalan Teluk Batu 1,
Batu 4 1/2, Off Jalan Kebun, Section 36,
40600 Shah Alam, Selangor
Tel : 03-5162 6146

Wilda Machinery Trading Sdn Bhd
No. 29-9 & 10,
Jalan Loke Yew,
55200 Kuala Lumpur
Tel : 03-9221 2430

Shin Tech Electric Tools
96L, Seberang Jalan Putra,
05150 Alor Setar, Kedah
Tel : 04-732 0810

Sengle Hardware Engineering Sdn Bhd
No. 89, 90 & 91A,B,C,
Seberang Jalan Putra,
05150 Alor Setar, Kedah
Tel : 04-734 3333

Ping Huat Engineering Hardware Sdn Bhd
No. 4218, Jalan Kg Bengali,
12200 Butterworth,
Seberang Prai, Penang
Tel : 04-333 1473

Seng Heng Engineering Sdn Bhd
12, Jalan C.Y.Choy,
10300 Penang
Tel : 04-261 6564

Yeoh Leong Machinery Sdn Bhd
No. 1-3 & 3A,
Jalan Sultan Yussuf,
30000, Ipoh, Perak
Tel : 05-255 7668

Heap Soon Hardware Machinery Sdn Bhd
No. 27, Jalan Bandar,
36000 Teluk Intan, Perak
Tel : 05-621 2236

Goodwill Machinery & Industrial Supplies
No. 457, Jalan Zamrud 6,
Taman Ko. Op, 70200 Seremban,
Negeri Sembilan.
Tel : 06-761 8768

Tiam Heng Machinery Sdn Bhd
No. 100-D, Jalan Kesidang 2/24,
Taman Kesidang 2, Bachang,
75250 Melaka
Tel : 06-335 5879

Yong Seng Heng Trading Sdn Bhd
41, Jalan Salleh,
84000 Muar, Johor
Tel : 06-952 1712

Globall Hardware & Machinery Sdn Bhd
No. 34 & 36, Jalan Rosmerah 2/16,
Taman Johor Jaya,
81100 Johor Bharu
Tel : 07-351 4117

Wellmac Machinery & Hardware Sdn Bhd
48 & 50, Jalan Sutera Tiga,
Taman Sentosa,
80150 Johor Bharu
Tel : 07-333 8911

Emas Hardware & Machinery Sdn Bhd
1370 & 1372,
Jalan Mersing, Taman Ria,
86000 Kluang, Johor
Tel : 07-772 3193

Tat Agricutural Machinery Sdn Bhd
1-2, Jalan Delima,
Pusat Perdagangan Pontian,
82000 Pontian, Johor
Tel : 07-688 1988

Syarikat Unicorn Engineering
3535-A, Jalan Kuala Krai,
15050 Kota Bharu, Kelantan
Tel : 09-748 2302

---

Added on March 12, 2012, 3:06 pmBeginning of April, I will keep you updates venue and date. In roadshow, you can get great KANG TAO and freebies plus free demo on powertools. You can try and feel the tool performance before purchase.

This post has been edited by jeffreylam: Mar 12 2012, 03:06 PM

 hr2230_e_view_1_.pdf ( 1004k ) Number of downloads: 32


HR2230 Rotary Hammer 22mm

Continuous Rating Input : 710W
Capacity :
Concrete : 22mm
Steel : 13mm
Wood : 32mm
Impacts per minute : 0 - 4,050 ipm
No load speed : 0 - 1,050rpm
Length : 357mm
Net Weight : 2.4kg

thanks alot do keep me posted, of the shop listed above which shop is selling the cheapest?

---

Added on March 12, 2012, 3:06 pm

Beginning of April, I will keep you updates venue and date. In roadshow, you can get great KANG TAO and freebies plus free demo on powertools. You can try and feel the tool performance before purchase.

[/quote]

Nice, now we don't any problem to find Makita's power tools. Cheapest price,? Aiya, just call the shop's phone numbers la.Not cost much to to call laa..

HR2611FT... wow... this is the latest Makita corded rotary hammer. ... I already saw the announcements last year in Makita Japan website.

Honestly, I never expect it going to be in Malaysian market that fast.

Anyway,, thanks for the update.

bahathir last time i call for quotation for makita hr2810, but alot cant give me exact price or they will tell u will call back and end of day no news. usually those smaller shop also dont have full range of item it would be nice if some one can compile the price list and also price of bit for refrences.

In my case, I called Jasakita, and they pointed me to the hw shop address in the first page. I called them, and they have HR2810 and HR1830, which both I wanted to see before I want to buy.

I think all the official Makita resellers can be helpful. If not, complaint it to Jasakita.

email them no reply.. need to call and fuuu their marketing mgr...

I think you emailed to their old address ? LOL
Anyway, what question you have for their marketing mgr ?