nichalasteo (not sure if spelling is correct) sells it by meter in the bulk section. can order from him.

I can't seems to find it, can you please help to look for the name?
or anyone know?

thanks.

for stuck fan, move only if I spin it once, any advice?

Get the fan removed and clean the motor through out...make sure dust are removed and grease or lubricant is applied after that ..

can that fan be open up?? it looks like all sealed? any pic of a fan being open?
anyway, i bought some tools in a DIY shop just now:
- motor oil, a few drops make the fan revive
- 1 set of RM6.5 multi screwdriever which help me to unleashed the 4pin ATX at last!!!
with this set of screw driver, I think I can open any molex, 4/6/20 pin ATX
- also managed to get 1 meter of black only colour heatshrink from an electronic shop.

any idea if I need to plug this (6 pin Auxiliary power connector) somewhere on my Intel mobo? I had forgot to label this one.

I read somewhere and it says:
"The aux power cable was added to provide extra wattage to motherboards for 3.3 and 5 volts. This connector is rarely used. It occasionally shows up on older dual CPU AMD motherboards"

this 2pictures for standby in any case anyone forget which is which ..

some psu has a missing wire ( that's the white 1 u see in picture )

if u forget any wire, PM me the brand & model, we've a record of basically all the brands in the market.

otherwise, below 2picture is most general.

all black wires are same?can relocate them?(between black wire only)

PSU Sleeving hands on lesson @ KL, during BBS 7

check out signature below for details.

Just pop by, bring ur pus or any other loose wires . Get some sleeves from us & we'll teach u on the spot how to do it right.

wah . then i must got they and see our sleeve master perform in action ...

anyway it would be at LYP or the car park.... coz it's dying hot in the car park .. i wonder how i could sleeve with sweating hands..

I am looking forward ...

yah finally.. uglyvamp offers a course for sleeving psu. wanna look forward to it!

Hmm i found that VIZO cable sleeve kit that can expandable, what does it mean ?

---

Added on May 10, 2007, 4:29 pmJust now i try for a old PSU to remove those connect, but i stuck on that SATA power and ATX ......
SATA is can't removeable ..... what to do for it if i want sleeve ?
ATX i slot 2 pin inside also cant release the hook....

This post has been edited by vincent09: May 10 2007, 04:29 PM

still planning for it

mostl likely i'll fix it on a sunday, between 7.30pm to 11pm in my hotel room @ sunway pyramid. the room there is much bigger, can easily accomodate up to around 10 guys & we'll all sit on the nice carpeted floor with air-con. i've to do it nite time cos daytime got to attend to the sales.

wait for me to update this one ok ..

my gf will be around to help with the guide on the spot too if i'm busy with other stuffs.

some tools i need u guys to bring are :

1) scissor
2) flat head screw driver for spectacle tiny screws ( must need )

others like below if have do bring, if not we'll provide.

3) scotch tape or masking tape, small one.
4) staple bullets
5) Plier
6) soldering iron, solder & flux ( in any case someone break any wires )

yah it's great but held at night ... . .. . . .. . . hmm i hope can make it ...

dude, pls pm me the way how to remove my cm stupid factory sata connector please.. ><
thanks

any idea on how to remove this type of sata connectors until it become like this :

Need help here..
I'm using Ennermax Infiniti 720W, the socket to PSU looks like this... I don't know how to remove this...Or actually is it necessary to remove this head?
Cause I see it will be much easier to sleeve if this head is removed..



Attached thumbnail(s)

refer to 1st page of this thread...post #4

it shows how to remove the pins for the 20/24 atx cable.

use the same exact method

how to seperate between those 2? because my PSU sticks those 2 wire togather, and i can't seperate it to sleeve it seperatly

hey all

on the 3rd June between 7-8.30pm we'll be having our dinner at this Asia Cafe ( big open air cafe around SS 15-17 ?? ) near to the previous lanparty area.

guys living around Subang can come here find me & I'll tips u on the sleeving. We'll guide u on the spot.

things to bring down :

1) scotch tape
2) flat head screw drivers
3) scissors
4) lighter if possible if not i provide
5) staple bullets.
6) plier if possible ( for ATX pins )

Inform me b4 coming down k ..

More details of it & my contact number on my signature below.

Cheers ....


if its the same as the one shown in picture then easy la. just pull the wire out then push back again right ??

if u want that type of connector then i'm afraid u'll have to purchase them seperately.

we used to have UV sata right angle as show in ur picture but all sold out already.
with that type of right angle sata, we can make our own sata power cables


This post has been edited by uglyvamp: May 31 2007, 02:34 AM

me also penang kia....i bought sleeving kits from this nichalasteo also....not bad....
and friendly tho

Hello, just would like to share with you. I've make my own 24 pin removal by using small screw driver and dremel.