Alex stated before.. our standard valve can tahan up to 11.5k RPM only.. correct me if i wrong.. i forgot roughly the amount d.. but 11k confirm is got..

anything beyond that.. kalau nak cuba.. rosak or anything.. don come find us.. haha..

This post has been edited by Aaron135LC: Aug 23 2011, 12:12 AM

haha, operate exhaust looks ori, sound ori..... if not remove airbox, u x know whether is mod or x....

it might fit in 62mm uma, u also dunno, u come sek 16, got few this new lc all quiet, 62mm uma block, 28/30mm carb, operate exhaust and etc...

nowadays, all quiet quiet no need noisy noisy.....

@NewGuy: Stock LC5 stock exhaust tip is bigger than older version.
@melvinho: Can confirm?

---

Added on August 23, 2011, 12:31 am@Aaron: I think that was the max allowed piston speed before physical limit of metal fatigue... forgot the RPM, I think was 14k for stock stroke.

This post has been edited by alexei: Aug 23 2011, 12:31 AM

@Aaron According to foreman yes..Our ori valve maximum just can reach 11k or the valve and valve spring will gone faster.

@Bro eric Lol...~I dont know la but that bike really fast....><

[quote=alexei,Aug 23 2011, 12:28 AM]
@NewGuy: Stock LC5 stock exhaust tip is bigger than older version.
@melvinho: Can confirm?

LC5 stock exhaust tip is bigger than older version but the pipe under the footrest is smaller than older version, cause air-flow semput semput , and cause top speed decrease.

[quote=melvinho,Aug 23 2011, 09:06 AM]
[quote=alexei,Aug 23 2011, 12:28 AM]
@NewGuy: Stock LC5 stock exhaust tip is bigger than older version.
@melvinho: Can confirm?

LC5 stock exhaust tip is bigger than older version but the pipe under the footrest is smaller than older version, cause air-flow semput semput , and cause top speed decrease.

[/quote]

The manifold no need so big, the manifold for NOB1 SSS is good enuf but the muffler...... , big big manifold high FC....

60mm and above different story.....

The chrome/steel color available in the market,tats suitable for 60mm and above...

---

Added on August 23, 2011, 11:14 am[quote=alexei,Aug 23 2011, 12:28 AM]

---

Added on August 23, 2011, 12:31 am@Aaron: I think that was the max allowed piston speed before physical limit of metal fatigue... forgot the RPM, I think was 14k for stock stroke.

[/quote]

no matter wat aftermarket CDI all will cut at 13/14k at neutral....and 10/11k at 4 th gear

the difference is how smooth and the CDI can tahan stress it is given.....

thianz and mine aftermarket CDI, same as the above even though different brand....

I heard oni 1 bike did not have cut off it is not sure honda/yamaha 150 2T bike, the owner the ref ref at neutral the bike kaboom.....

The owner do know about it so later claim manufacturer about the incident....

So anyone dare use really not cut off CDI, everyone mistaken the meaning cut off...

This post has been edited by NewGUY: Aug 23 2011, 11:14 AM

Bro eric.. It's possible the cdi handmade? Means got some engineering friend might can help do 1??

Anything also can, take too long time, aftermarket less than 200, for wat waste so much time...

Ppl custom certain bcos to expensive to get, y 1 waste time when already have and not very expensive....

The component u can get maybe not as good and u need crack your head to program inside.....

Really really tight budget can la....

BTW, u be his trial and error bike can la....

Y u can try so many tires, u can also try the cdi, about same price range.....

No...original bike foreman recommanded better dont change cdi and etc..

CDI just extra RPM and xtra pickup, u x always rempit, wat goin to happen?

Like yours, hardly use except for TT, ori or aftermarket CDI does not cost any problem...maybe for very long distance maybe can know lo....

U control your machine, no the machine control you....

Bro, you need use your bike more often, only you can only understand it...

Sometimes, the pomen no really know your bike also....bcos u ride your bike, not your pomen ride your bike.....

Ok...I always use my lc la bro..><

@newguy: so the cdi tat have thailand yamaha cop on it can be safe to used? is this cdi actually ori from yamaha thailand or just local made? I wana try hope2 the cdi can add a little bit kph for forth gear..

i think a lot of ppl using....kaboom everyone already know la.....

ori or not, i dunno...

if ok it go to 10k, ori spring kenot tahan 10k or 11k rpm....

change valve spring before change cdi....

so need to change valve spring oso, hmmm will think again...

Guys.. last time i tested with my friend green colour stock lc...

my friend meter showing speed 170km/hr.... but mine is 130km/hr ?? at the same row.. that means my lc meter is accurate or there got lot of different lc meter ??haha .or i just syok sendiri...lol
maybe 3~4 type of lc meter for lc before 2011 ?



This post has been edited by mls_gamer: Aug 23 2011, 07:08 PM

meter speed different..

I give u a few cases :

1) if ur bike front fork dropped lower.. rear tire bigger.. when u ride the bike.. ur weight tends to shift more to front.. resulting in ur speedo becomes indirectly heavy..
2) if the bike front stock height and tire all same.. ur speedo i dunno what to say.. light..?
3) if both ur F and R tire also big.. ur speedo will become heavy.. when it becomes heavy.. sometimes right.. is the meter the one playing mind games with u..

like last time mayb u can go 140km/h.. but after change F and R.. ur speed decrease to 120-130km/h.. but actually.. both speed the same.. just that the time for u to reach that speed might become slow only..

example for car.. if ur car only got 1 person in it.. then ur accel and speed easily achieve.. but what if u fetch ur car full load.. accel will decrease.. but the top speed u will easily get over a period of time.. because ur car more heavy.. it sort of like becomes a kinetic energy pushing ur car to go further..

this is what i experience when i drive with family and alone.. alone very easy naik.. but the top speed need to gamble with wind.. if u fetch a load.. u will notice ur car can go even more easily..

but of course ! don try this ! be careful..

This post has been edited by Aaron135LC: Aug 23 2011, 09:18 PM

@melvin: thanks for confirming. the pipe section under footrest, is manifold. So, comparing LC5 and older version, u got the exact measurement or not? I remember NewGuy posted before, but forgot where I kept that...

@NewGuy: Can post the measurement again? Sorry ah...

To me, CDI is a black box, and also an expensive one... If I have 100+ ringgit to spend, I'll buy a gift to the girl I like.

This post has been edited by alexei: Aug 24 2011, 04:04 AM

@Bro Alexei: Yes..I knew it..I know world is a very big forest..But every trees had their own special bro...I really lack of comunication with girls....Girls always said me not enough mature cause talking to them i must like this or not girl's r felt that me too serious... And my hobbies is rideing and bulid plastic model... So i really lack and less comunication with girls...Even in my college i also taking Computing courses...All guys even have girl's also got bf 1....>< Really damn dissapoint....
(P/s: Bro Alexei got gf already? )

@shyan - for now.. better u concentrate on ur study/hobby 1st.. woman = problem.. wakkaka.. i forgot where did i saw a formula related woman with problem.. but now.. better concentrate on ur stdy.. in future.. when u are successful on our carrier.. u no need to chase girl.. girls chasing u..

@newguy - sorry to ask again.. did the shop at sek 16 got sample lc that already modified the mono? i wanna test 1st the mono keras whether suit with my taste or not.. rm80 right?

This post has been edited by budakmentah: Aug 24 2011, 12:00 AM

@shyan : learn up skills n lear more new hobbies.. if u didnt improve.. how do u expect girls come to you..? right..?? i mean.. u wan to get them right.. but don expect them to change for u.. u need to learn more things and learn how to adapt.. =) for example.. learn ur language.. make it strong by reading books.. studying about computer.. u need strong foundation of languages.. =)

@mentah : i think i know what formulae u referring to.. hahhaa.. damn complicated formulaes.. but in the end woman = money or problem.. forgot d.. hahaha



this becomes more to girl talk liao.. LOL