If you check his worklog, he modded the PSU mounting plate. And no longer using the L-Shape connector for the PSU, he direct wire the cable to the PSU cause after shifting the PSU further out to the front, u are not able to use the L-Shape PSU connector.

I can sent u the link if you want...

U can get extra 2cm space after u reverse the PSU mounting plate, but u no longer can use the original L-Shape PSU connector.

I been seriously plan to use mcr220 on this case before

hey guys...
need some help here..
actually this is my first time try to OC.
I did what the (How to overclock Glossary) from bit-tech.
but, after that i couldn't get into the OS at all. (windows 7)
lol.
so, i have to choose for system restore instead.. lol.. a lot of my logs wiped out.. heh.
and, i don't know where to find the BSOD logs...
i looked in the event viewer..
it says like this.
BugcheckCode 0
BugcheckParameter1 0x0
BugcheckParameter2 0x0
BugcheckParameter3 0x0
BugcheckParameter4 0x0
SleepInProgress false
PowerButtonTimestamp 0

is ti because of my ram? hehe.

---

Added on May 20, 2011, 10:34 amlol i just changed the PCH SATA Control mode to ACHI... that's what makes I can't Log in Windows.. I changed it back to IDE .. now can log in with the current x45 multiplier.. hehe..

testing stability now. hehe.

This post has been edited by ashraful: May 20 2011, 10:34 AM

BSOD codes for overclocking on the first page.
Probably Vcore to low.Give more details.

lol.. already know what makes the problem... i changed the PCH SATA control mode.

Anyway, i want to change my ram to corsair 8GB DDR3 Vengeance CL8.
I'm afraid that it will noat actually brings any difference compared to my current RAM. ( of course now is 4 GB only.. )
I mean, might as well i bought the 1333 another 4GB if it does not makes any difference. hehe.

Thanks~!

Depend of your bugdet,if is cheaper buy another indentical set of 1333 2x2GB.
8GB DDR3 Vengeance CL8 you must run separatly.

This post has been edited by stasio: May 20 2011, 10:53 AM

yo stasio dude

can u pass me those bios u were talking about?

thanks

hey guys , can help me diagnosis ?

i5 2500k
Asrock z68 extreme4
1.30Vcore 4.5ghz



The run got the error when it was started for 4 5 seconds Any other information you need to diagnosis this ?

and Who has good OC guide for p67/z68 astreme 4 6? I found many guide in internet , tried many of them . But still getting this error

so.. the prime 95.. should i test the small or large ftt?

got quite a dud myself here

4.5ghz require more than 1.45 to be stable

for me i always use small as it stress the cpu more

but im not really sure

maybe others can help

my prime 95... also saying that worker #3 always fail. 1.30Vcore 4.5ghz
Hardware failure..
I'm afraid that my RAM is the one who bottleneck this oc thing.

what's u guys vtt voltage on??

tried 1.15v or 1.2v yet??

my vtt is 1.12v
vcore 1.3v

i'll try increase my vtt then. hehe.

here's the temp of mine



cant change to a dual rad but i can add another single rad

Send PM.

Increased VTT to 1.15V wroker #3 can prime no prob.
But then, suddenly my worker #4 says the same thing... (hardware failure)
I haven't change the Vcore yet.. still at 1.3v..

Same Vcore as my on 4.8GB.Testing BIOS F6 for Z68X-UD7 on my P67A-UD7.

lol.. i retest it again.. now it's ok..
I want to wait another 1 hour. hehe.

Currently running prime 95..
Praying that it'll be fine though. hehehe.

---

Added on May 20, 2011, 12:54 pmI have a question.. currently i'm doing multiplier x45..
but when i primingg, it turns back to x34? why is that so?
Thanks~!

This post has been edited by ashraful: May 20 2011, 12:54 PM

Once you you are in Z68X BIOS,normally flash with Q-Flash,FlashSPI or Touch BIOS any original BIOS (not modded).
Btw,here is latest beta BIOS:
GA-Z68X-UD4-B3 - F7a

This post has been edited by stasio: May 20 2011, 12:57 PM

now i know... it's my easy tune problem...

everytime i opened my easy tune,
the multiplier went down form x45 to x 34... why is that? hahah.
Now it solved... unless i open easy tune again. haha.. i think so.


This post has been edited by ashraful: May 20 2011, 01:31 PM