Hello,

Wanna get ur advise on my CPU temperature problem. Is it normal at idle my E8400 temp is 47 - 48"c. Busy is about 51 - 55 "c.

My Rig : E8400@3000Mhz no OC
Cooler Masterii Gemini @ 1928 fan speed
2GB KIngston 1066



Tq


raifalove

Hi Guys,

May I know do you guys enable HPET functionality??

-pWs-

Which temp reader are you using? Try using RealTemp then it will show 10'C lower which is the assumed correct temp for 45nm processors...

my e6600 is also a B2 stepping if im not wrong last time i OCed to 3ghz on stock cooler, the idle temp is 45C and load temp is 62C.. and its quite hot.. hmm... maybe ur casing ventilation is bad or the ambient temp in ur casing is high... as for cooler get xigmatek... its the best bang for bucks...

---

Added on May 25, 2008, 9:07 pmuse realtemp to read the temp... real temp shud be 37-38 idle and 41 -45 load... if that is so then ur temp is fine when not oced...

This post has been edited by IcEMoCHa: May 25 2008, 09:07 PM

Then it should be something wrong with my proc or the stock HSF not installed correctly. But i installed it firmly and it's not loose Only downside is i have not re-apply any thermal paste as i have none. But anyway, seriously considering getting the XIGMATEK HDT-S1283.

I'm using Gigabyte 965P-DS3 and i'm worried the NB heatsink will block the cooler and i can't install it as the height of the NB heatsink is quite tall. I measured the height using a ruler and it's approximately 3.4cm.

Anyone with XIGMATEK HDT-S1283 installed it on a GA-965P-DS3 before or is confirmed sure that it can be installed with no problems, please let me know

Many thanks.



This post has been edited by Archaven: May 26 2008, 01:20 AM

3.4cm? I guess that's the same height with GA-P35-DS3, measured its height once and its 3.4cm as well and S1283 fits on it.

what about the ventilation inside ur casing?... is it good?..

any1 tried Q9450 yet? hw far can it go?

My Q6600:

CPU : C2Q Q6600
CPU Clockspeed : 4.0Ghz (445x9)
Motherboard : DFI DK P35 T2RS
RAM Model : Crucial Value DDR2 667
RAM Capacity : 2x1GB
RAM speed : 445MHz, 5-5-5-15
RAM mode : Dual Channel
Cooler : OCZ Vendetta 2
Time : 12.734s



This post has been edited by Ryo: May 27 2008, 12:04 PM

maybe 3.6ghz with ifx-14 and 4ghz with wc.. if it doesnt hit fsb wall..

the safe spot is actually 3.8 for both WC and air.
its kinda weird cause the cooling does not impact it as much as it did on the 65nm

I think it's due to the faulty thermal sensor. My chip idles at 44C irregardless whatever speed or voltage

kinda.. but at 3.6 the temperature is quite high with air cooling..

im not sure whether it is faulty or not but i guess its time for a new IR sensor!

well actually if you notice the temp diff between the two speeds are not that significant and its probably due to the fact you dont have to pump up that much voltage for that small bump
well, atleast that's what i see on XS as of now

hmm.. i see.. but the quaddies are hot even the voltage is low... load temp around 65C @ 3.8ghz with ultra120x...

Hi,
I having "Clock interrupt not received on second processor with in the allocated time permitted" BSOD problem even in stock speed.

FYI.
1. Bios already updated.
2. Tried PSU.
3. Reinstall new windows (32bits & 64bits)

Until now, I still having that problem. This problem occurs around 3-5 hours stressing.

Any idea guys? Please help.

Thanks

-pWs-

This post has been edited by -pWs-: May 28 2008, 08:27 AM

looks like mobo faulty to me..

Motherboard highest chance of being faulty... Next is processor ~.~

Oh Gawd ~~~
Any tips to test it out??

-pWs-

RMA it..