yes mine 1 is old 1... but i got bubble inside...

but then where u hide this??? since all panel close.. how did u route the cable?

ur reservoir is revision 2... can outside down... to prevent the buble, by letting coolant in from up and fit a fitting inside the res, then attach a tube to the fitting... or filled the res full...

another option:

niclas

I'm waiting for Bitspower X-Station red from vlad

Wan to ask,if i nw using rev>pump>gpu>cpu>rad>rev again..is tis ok?or my cpu wil getting hotter since it getting the hot water after d gpu block?

should probably stay with it since its all setup the difference isnt that great..

Eh..coz nw i wan to find d finest setup..haha..

The difference is minimal as the whole loop will get equilibrium.
I'd say ur setup is good to go. and no worries bro ur 5850 wont be as hot as gtx480

+1 Thermal Equilibrium

few notes
u will only see non-equilibrium if u stress one component at one time
say like a proc thats hotter than a gc

but in real world.. this wont be true
most of the time ure cpu and gpu temps are around the same.

---

Added on August 22, 2010, 12:10 pmok doing this setup on a triple look with a overclocked i7 and a single gtx480
putting the gtx480 just increased my idle and load temp by 1 C

This post has been edited by cstkl1: Aug 22 2010, 12:10 PM

The u-shaped tube is about to kink when I set like this

no wonder my coolant flow sucks & no fountain effects in the res
actually can be fixed by cable tie but looks bad

So I modified abit to

now I can see the coolant flows smoothly

Oh..is that jus d 1c diff frm d single loop?i mean is jus cool the cpu block only..correct me if wrong.

Pump - Cpu - Mobo - Rad - Res - Pump

Rad Triple Rad

vs
Pump - GPU - Cpu - Mobo - Rad - Res - Pump

1 C difference on GPU and mobo temp

then

Pump - Gpu - Cpu - Single Rad - Mobo - Rad - Res - Pump

1 C difference n Gpu only.

Actual influence of flow rate on system temps
http://www.xtremesystems.org/forums/showthread.php?t=253337

Dual Loop vs SIngle
http://www.xtremesystems.org/forums/showthread.php?t=254683

This post has been edited by cstkl1: Aug 22 2010, 01:23 PM

done with my cable management, however, still got little cacing left..



using phone camera, quite blur..huhu..

Wa..thats is too diff for me to undestand it..haha..i didnt use mobo chipset cooler.

Find the cleanest tubing setup with the shortest tube length will probably be best than having a 1-2 c delta difference imo.

Oh..its mean d short of d paip lenght wil b d better performance?

---

Added on August 22, 2010, 2:36 pmwhich is most correct way after d pump go?is it go radiator>block or block>rad?

This post has been edited by alan kc: Aug 22 2010, 02:36 PM

thanks the tips....

thanks owikh84, i found the solution easy n save money for radiator fans cable connect..

so here spamming part....



guys, is it after shut down computer, the coolant will flow back to reservoir rite?

performance part



vcore in bios 1.375v... not really best performance yet... bcos tubing got a lot of bubbles.....

custom water cooling really best performance indeed, i tried b4 highend cooler Thermalrigh True 120 BE, Coolit Domino ALC, etc...

True able to withstand to 70+ full load 3.6Gz, while Domino ALC around nearest 70+- full load... not really good but

water cooling best ever.. of cos money also best ever...

as for problem part... i have dy solved it... will post new performance in later days.

This post has been edited by subrok007: Aug 28 2010, 10:45 AM

Is that ur problem is 1st time or after many time on off stil same?

on and off many times still same... pump drain almost finish then coolant from rad just filled back to res causing air trap inside tubing to pump..

you need to bleed your loop.

Bt is it running few time its wil ok right??

---

Added on August 22, 2010, 3:24 pmFrm ur rev,is it ur inlet placing at up then ur outlet placing on bottom?

This post has been edited by alan kc: Aug 22 2010, 03:24 PM