alan kc,

yes my inlet is from upside, outlet is downside...

supernothing,

bleedy loop is let the small bubbles out... but my problem is feel like reservoir capacity too small for my whole loop...

the problem is like that...

start pc, pump pull coolant frm res, coolant almost finish until u can see no coolant inside res, then baru coolant from inlet filled back to res... that's y i believe that happening causing air trap inside tubing.. am i rite??

U try d inlet and outlet at bottom,i thk wil solve ur problem bro..haha

haih... but my tubing not enough length liao...

and also make it more messy inside... try the tubing as short as possible...

any idea bro?? instead that

bro dunnoe it is i wrong or nt ahha..
but i really tested this before so i share here...
for ur problems... u need put in and out flow under the reservoir lo..
i testing in my 1st time for my DIY reservoir cz main reservior hvnt come and no stock.....
ur problems only be fixed it when both in and out tube water flow under the tank =)
correct me if i m wrong.. newbie here learning

-----------------------------------------------------------------------

edited
for ur wc get full coolant must needed the reservoir pressure =)

This post has been edited by yuanbao: Aug 22 2010, 03:35 PM

I think its common for the res to be upside down if it coolant level drops u can try having a drain tube to have some extra coolant place to flow to so when u turn off the rig to prevent overflow or install a 2nd bay res like many of the xs forumer.

tried from me le... if u dun wan get extra tube u need re-setup ur wc -.-
which i think u wont haha..
get a value tube for it la... =) then should be working fine le..
makan roti 2 hari can liao lol

bro u mean both inlet and outlet must place at bottom rite?


yes, i scare it will overflow when i shut down my pc.. but is just ngam ngam if more abit sure overflow liao..

so u idea is start pc then filled coolant... let it running. then prepare drain tube for overflow after shut down??

jump your psu, don't run your pc while leak test/adding coolant/bleeding. very the dangerous.

Haha..if nt buy d combine connector at kedai logam wit 2 clip,then jus sambung d paip..u using 480 rad,looks like u really d extreme oc..haha.

jump start ur psu bro more easy like that when u try to fill the loop...

yes both tube must under the water pressure then only all bubbles will slowly move out from ur stuff..
this need ty my sifu CLAW... teach me de haha



lol i suggest he was =p

yup... will try adding coolant again... see how's going...

leak test pass... no leak...

wah sambung paip very dangerous lo... will leak 1...

will looking clawhammer again for tubing part..

yes....

any1 tried b4 using swiftech reservoir with quad radiator?>



This post has been edited by subrok007: Aug 22 2010, 03:51 PM

i tried for 10 hours =) lol anythg u wan noe?

yuanbao..

u using Swiftech MCRes and quad radiator? that small reservoir enough for quad radiator?

Bt if u dun change d inlet position and continued adding d cooler,i scare it wil b overflow when u on ur pc.

res size doesn't matter. what's important is how you setup your loop.

Haha..actualy that is enough for all rev no matter how small is it,bt d coolant level must cover d inlet and outlet level enough.

lol i use 2litres or water but when fill like around 1 liters +- it see almost full for all my wc (cpu wb + res + quad XSPC rx480 + tri swiftech mrc320)
answer for u this u need to keep throw in the coolant until u see the mcres v2 only got bubbles lo... (i only keep refill 3/4 while fill in all wc stuff)

this is wat i thinking now... may be will change inlet position to bottom..

or ask clawhammer for solution.. any how still need to buy tube again.. money gone


how said so?? not really understand since this is my 1st custom wc..

1st u need buy tube already is 100% solution just put the inlet bottom sure solve de =p
2nd is reservoir just to storage coolant and make inlet +outlet oso got water pressure so ur system can pump the water nicely and get the actual preformance + no more space for air...

i oso 1st time come learn together =)

This post has been edited by yuanbao: Aug 22 2010, 04:00 PM