Impressive result! I think I'll give it another go later.

At the end it depends on luck as overclocking never guarantee the same result with the same chips. But, the fact is very clear. Any Hynix BT-J, BT-D43 or DT-43 is a good chips and underated by many as they're not so popular among western overclockers. If lady luck is on your side, a good Hynix chips will outperform some average premier chips like TCCD in term of high FSB and tight timing. And with max vdimm on your board like 2.8 ~ 2.9v, the Hynix will always better than any Winbond BH-5/6 or UTT.

[WTA]~ I'm having 512 mb KVR PC3200 with Hynix chipset and wanna get anotehr stick from my friend,but just wanna make sure if idfferent chipset will it affect dual-channel capability ? coz the 1 my fren selling is same model KVR400X64C3A/512 but different chipset (Mos), i heard 'soulfly' previously telling that different chipset does not matter as long as same type (and is it recommended to be same batch of memory? )

Dont need worry bout it friend, it would be jus fine..
But one of the sticks might reduce or in other words holding back the other stick as u began ur quest to overclock..

so how bout ur pentium rig? can ur bt d43 doing 264fsb 1:1 on dual channel ? mine cant...

on my pentium i cant boot with 1t timing(cpc on)...
and the ram a bit choosy on the dimm. only managed to get higher on dimm 1 and 3. maybe its the trouble on AI7.
i managed to get able to do 250fsb 1:1 2.5-3-3-7 on 2.9vdimm.
my proc limiting me to reach higher clock.




Attached thumbnail(s)

wow.. u all set to 2.9v..

later no prob ka?

sory me not so new in oc...

It shouldnt be a problem UltramanToron since these Hynix chips max out with only 2.9v vDimm. Anything higher wont make any differences.

2.9 is max if i'm not mistaken if ur using single sided chip ram,
i knew there's ppl even feed the ram with 3.1vdimm on double sided chip ram.
i play a lot with 256mb ram single sided so i cant tell more. even when i tested zamree7 ram i didnt dare to feed it 3.1vdimm. max for dtd-43 i feed is 2.9 n no more than that.

just asking the timing the lower the better rite? if both at same speed and 1 is 2-4-4-7 another is 3-3-3-8 which 1 is better ah?

i think this was discussed and tested before...
it work best at 2.8 - 2.9v
higher than that might not perform well

My DT-D43 doing 250 FSB 2.5-3-3-x 3.1v
8MB super pi passed.
3D mark passed.
Prime blend test passed.

Below is 8MB passed.


[attachmentid=51944]

wow....
u r lucky to find a d43 perform well using 3.1v

I found running 3v cannot pass 8Mb

wowwweeee! ur ram is 512x2? double sided is it? running on dual or single?

mine 2.9v - 240fsb - 2.5-3-3-x = cannot on oledi

3.1v need special cooling or not? watercooled?

This post has been edited by UltramanToron: Mar 26 2005, 11:13 PM

nonit special cooling.... if u scare then put some ramsink on it ram can handle 3.3v+- without any problem.. depends on ur need

juz shoot whatever juice u think the rams can take mostly is stable voltage coz some rams doesn't take high vdimn.... if u scare.... put some fans and blow at them

just for fun nia...
slap in a stick of 256mb bt-d43 and run memtest86

bt-d43 325AA
268mhz, 2.5-4-4-11-1T with 2.9vdimm



i got another piece, but unluckily cannot boot that one. neenong neenong neenong came out from the internal speaker
i guess kena electrostatic

hey, just tot you guys should know that Cycom still has one last pair of 512M Kingston dt-d43's just got the 2nd last pair at 175 apiece so you guys shld prob hurry...

will do some benching once i get my mobo back from rma

jwyj's 512MB DT-D43 508PA
double sided single channel
250mhz 2.5-3-3-11-2T, 2.8v



p/s: using 2T bcoz nForce2 is not very friendly with double sided modules