How bout this DTD-43 doing 277fsb... thanks to zamree7 for lending his ram n do the testing together...
i think i need 2.9vdimm to get this ram max out...
mine only max out 264fsb 1T...

see the attachment


Attached thumbnail(s)

dunno if its work on others, i used my amd rig to test it on Neo2 Platinum.
264fsb 1:1 2.5-x-x-x 1T at 2.8vdimm n i noticed DTD-43 dont like divider.and i use dimm 1 and 3.
and i'm on 1.36beta modded bios.
didnt thinkin bout doing a print screen coz thought its just an ordinary result
will do the print screen later coz still cant reboot my system due to priming at 250fsb 1:1 2-5-3-3-6 1T at 2.8vdimm.

This post has been edited by rzonealley: Mar 20 2005, 02:12 PM

still can find DTD-43 in LYP but only for 512m ram... not 256...
try searching in Czone Cycom Robyncom. wish u luck huhu

hope to see some result to arj.

zamree7's DT can do 2-2-2-5 2T at stock vdimm at 210fsb but didnt test any further since we wanna test the highest fsb the ram could handle.

and as i mentioned above the ram max out at 277 with my limited vdimm at 2.85v. i'm sure it can go more with 2.9vdimm. but yet its only the highest it can go but not memtest past.

512x2 so far memtest past at 260fsb at 2T timing.
compared to 256x2: the 256x2 could handle more tighter timing
and memtest past at 1T timing is 263fsb 2.85vdimm.
maybe this is due to the different between the single sided and double sided chip of ram.

btw hope can see some impressive result from u arj.
best regards.

found one btd-43 can do up to 264fsb...

and it on sale

http://forum.lowyat.net/index.php?showtopic=139863

on my pentium i cant boot with 1t timing(cpc on)...
and the ram a bit choosy on the dimm. only managed to get higher on dimm 1 and 3. maybe its the trouble on AI7.
i managed to get able to do 250fsb 1:1 2.5-3-3-7 on 2.9vdimm.
my proc limiting me to reach higher clock.




Attached thumbnail(s)

2.9 is max if i'm not mistaken if ur using single sided chip ram,
i knew there's ppl even feed the ram with 3.1vdimm on double sided chip ram.
i play a lot with 256mb ram single sided so i cant tell more. even when i tested zamree7 ram i didnt dare to feed it 3.1vdimm. max for dtd-43 i feed is 2.9 n no more than that.

opss my bad wrong pic. uploaded...
here's the screenies for the dual channel.
sorry for wrong pic. but this one is on 2.8vdimm only.


Attached thumbnail(s)

i dunno where to put it for me 2.9 is still safe level.
all the benches i did, i didnt put any xtra fan or cooling for the ram.
so if u hit 2.9 with xtra cooling i think it'll be better.

hard to say whats the best chip. KVR comes with many different chip.
most popular out of it is winbond bh5/bh6 but u need quite high vdimm
to make it fly.
but for midrange overclocker like me i would say hynix is quite good.
hynix comes with lot of series of chip bt-j, btd and dtd. all of them can be
overclock but even on the same chip the oc-ablilty wont be the same.
on intel i would put btd in it since timing is not so crucial part at intel.
but on amd i love to put dtd since the chip can handle lower timing
such as 2.5-3-3-7 at 250-264fsb.
just my 2 cents
good luck then i thought at 250 fsb btd could do the same as dtd but on max it will show some difference.

e-jump nicee...
its more like high performance ram.. up to 270fsb with lower timing.
memtest pass or not?
btw is it on 1T or 2T. if 1T its totally a gem.

berusahalah!!!!!
good luck mate. show some screenies later on will ya.

i have paired my DTD with Kingston Relabeled Chip and it make hell of a pair.
Can do up to 260dual channel. and i think the Hynix holding me back.
Coz the relabeled chip can do 264fsb 1T single channel on STOCK VDIMM!
i'm not lucky enuff to find a pair for that relabeled.

since u all talking bout UTT maybe u wanna consider TCCD and DTD50

DTD-43 is still can be found in LYP if i'm not mistaken but only for 512x2
but its nearly impossible to hunt em now.

@pizzaboy how bout googling Hynix DTD-50 its perform nearly similar to
TCCD but the brand using DTD-50 is not marketing their product here in
Malaysia such as Gskill and OCZ. and the price is a bit cheaper than those
TCCD.
BTW since UTT is easily can be found so still the best things to grab is UTT
but it will be great if can find DTD-50

yep double sided ram always have problem when running 1t compared to
single sided chip. thats why i prefer 256x2 rather than 512x2 when buying value ram. but if ur on high performance ram i dont think such a problem will be bugging u.

hope u can see it clearly.


Attached thumbnail(s)

nop. u will exactly see the writing winbond unless its relabeled then u just can see the dimples only and other writing.

what bios currently ur using?

u should try using the same bios as below