urgent! pls help.. anyone?

tested, still fail the memtest built in the bios
the latest bios, if everything auto still very tight timing to have them to run?

OT: kianwee, may i know why u changed the tccd to the VX series u using now?

Which bioses perform the best for you guys with BH5/UTT chips?

I tried a couple of bioses like 310 official, 313-1, 313-2. I now have trouble booting up my SLI-DR using the orange slots. Tried one BH6 stick in the 1st yellow slot and managed to flash back to 310 official. Put in 2 sticks Twinmos UTT in yellow or orange wouldn't boot either after that. Any idea what caused this?

Managed to boot in again using first yellow slot and I get a warning to use slot2 for single channel and 2 modules in slot2 n slot4 for dual channel. 

So I tried again in slot2 and 4 as recommended but I can't boot again. The LED lights show 1,2 and 3 lit up. Can anyone help me please?

tested, still fail the memtest built in the bios
the latest bios, if everything auto still very tight timing to have them to run?

Can anyone give me more information about RMA-ing a motherboard? I found the problem and its due to one of the connectors in dimm2 not making contact with my ram. There's one metal connector that appears to be flattened when the ram is inserted.

My dad got this motherboard for me from Viewnet in Lowyat plaza. Do I have to send the board back to Malaysia for RMA? Hopefully I don't have to and a local distributor can do it here for me

If anyone knows about RMA please enlighten me. My SLI-DR is inoperable for now

i think the warranty is quite good la...it's 5 years warranty isn't it...and i believe it's 2 years 1-to-1 warranty or izzit shop warranty...other 3 need direct with the manufacturer...just make sure u have their invoice or invoice number...maybe kianwee can confirm with his buddy over there...good luck

got back from viewnet...

btw is this abnormal?? i mean the system temp?? or those voltages?
noob here

noted 10q
normal? dunno y.... but seems i cant really clip that system fan into the mobo (i mean the dfi stock fan).

i already did this since the 1st day i bought the board.. but till now it still wiggles how ar?

erm my idle chipset temp is around 43C and when running stressprime it goes as high as 50C - 51C

yes it still wiggles but just 1 to 2 degrees... (42C<--43C-->44C)

i have one vantec iceberg chipset hsf.. never try it yet.. dunno whether it performs better than this DFI stock or not..

it does fit! i already tried installed it when first i bought it.. but then i opened it back

nice..do update bout the temp okey... coz i'm so lazy to open out my board since all my temp sensor wires are all hiding under the board.. 

last time i already removed the original pad that comes with the chipset fan. then i attached as5.. but still hot..   

28 degrees cpu temp? That doesn't sound right. Is that reading accurate? My watercool processor at stock settings and in a low 20's room is mid 30's only......

last time my friend with stock cooling said he was very proud coz he didnt need to invest a lot of money on heatsink like me, yet his temp still under 25C which is far better than my processor temp
then i asked him to update his bios and naahh his real temp is 45C ekekek

Wow! 10 degrees increase when you turn off the ac. You must have a big @$$ ac in your room!

29-30 on xp120 on stock setting maybe ok la...but on stock hsf, not quite sure...but as arj said...probably he got a damn cool room temp...mmm...r u in cold storage room kianwee

anyone got any suggestion on NB cooling stuff...air cooling please...the one that can be used on dfi nf4 ultra-d...my nb temp is not good la...mostly over 50c...frequently at 55c...already applied the as5 on the stock hsf...dun remember how thick it was...
any suggestion, guys?