1.52v

using xp-90c, vantec 92mm tornado@2700rpm.
the temperature showed is only 38~39

what i suggest is please check ur heatpipe.
ah_khoo, i suggested u to check ur XP120 heatpipe too...
lastime forgot bout it.
sumtimes heatpipe malfunction may cause this problems.

for my ex (xp120), i believe it was the problem w/ d bracket. the heatsink seemed didn't able to make full contact w/ d IHS, dats y the temp was so high, but come to think of it, i was play w/ 1.45V vcore (or above) all the time, so my assumption mite be wrong...

now i only play w/ 1.44V max, w/ my f64, temp highest is 48'C.

Hi guys,
Look at the pic, I cant go above 250HTT with my new rig, I am trying to find the max CPU speed. I have RAM timing set to (200 Mhz) 1/01.

Here are my spec:
Proc: Opteron 144 (bulk from Dinster, able to hit 2.9 like kacang, but I cannot)
MB: Lanparty UT UltraD
RAM: Kingston ValueRAM (2 x 512)
HSF: XP90 with delta sense flow.
GC; XFX 7900GT

Any advice from sifu?


Attached thumbnail(s)

bro, kinda high mine now priming at 2.8G @ 1.43v in bios reading or 1.42v in DMM reading, using xp90c pair with 92mm fan @ 2.2krpm, 38~39'c

haa.. haa.. haaaa.. dya expect to get 3.0Ghz wif KVR wif cheapop chippy?? dont dream

yeahh. opteron were hot. even mine 2.85Ghz@ 1.37vcore, load can reach 55c
im using XP-90 wif 80cm delta fan@ 25++krpm

May 27 2006, 11:12 AM
haa.. haa.. haaaa.. dya expect to get 3.0Ghz wif KVR wif cheapop chippy?? dont dream


You men the RAM?

u wanna try out freezer64pro?

ya lorr. KVR using alot chippy & the well known can get higher HTT was BT-D43. im oso using KVR currently & the MAX gan trigger is 285HTT. u need samsung base chippy to get higher HTT

good opty, 2.85G @ default vcore only

i think i must use divider for ur ram....then u can go over 250HTT !!!!!

Noob question: How to check? Need open and applied AS5 back then put it back?

sure maa. how can u check the HSF were properly seated if u didnt dig-out whole thing including Mobo

ps : my way is, b4 pasang HSf, take out all item & onli then seat the HSf

@gengstapo

your 146 able to hit 3Ghz @ what vcore?

havent try yet bro. im stuck at 285HTT onli. i dont have any better RAMs. currently using spare RAMs, cheapop KVR wif Bt-D43 chippy

Chep RAM can go 285HTT nice lah, me only can get 260HTT with 166 divider.

run 166 divider, the ram should be run in 250MHz

check ur heatpipe 1st.
does all carry same heat?
if 1 heatpipe is cool, then u might wanna try for heatsink rma.

if it is not, then as gengstapo said.
if not mistaken, ninja is same as xp-90, xp120, with the p4 clip...
so, u may wanna check does u screw it in a balance ways?
if not balance, then you need to really think about what to do.
might be ur clip is bendded, try fix it, so that provide a stronger force.

me on divider oso, 5:6


currently running PI Calculation 32mb on 2.9Ghz, on divider 5:6
the magic stepping no more when reach the 2.9 barrier. voltage feeded was 1.42 now
temp was 53~55c, damn!!

This post has been edited by gengstapo: May 27 2006, 09:25 PM

woow, 1.42v only