Proton Timing belt, timing bearing, timing oil seal - RM350
Gaido automotive fan belt 5pk1080- RM48
Bando fan belt 5pk865 - RM45
Proton Waja rear brake pad bosch (385) - RM 85
ENEOS touring motor oil 15w40 nippon oil 4L[NC]- RM75
Proton OSK oil filter small - RM14
REVO advanced engine friction reducer & modifier 30ml - RM45
Engine service charges - RM8
Off wheel balancing tyre 4pcs- RM24
Front and rear wheel alignment - RM35
Proton rear add universal cam bolts 2 pcs- RM70
Autolux brake bulb 1016 2pcs - RM10

Total price RM809

Is this price decent or kena ripped-off?

a lot of the items are little bit expensive, i assume they included labour charge in the parts.

nowadays normal metallic paint will cost around 1.5k - 1.9k.. if the shop offers below then 1.5k do research before send ur car paint there coz maybe they'll charge such low price for a lousy work.. if pearl.. it can vary from 2k to 2.5k.. depends on what kind of paint and how much pearl.. usually if a good paint garage will offer not to low and not to high price.. coz if its a paint job better u not ask for to much discount and low price coz they'll always match the painting workmanship with the price.. good price u get good result.. bad price u get "cincai" result..

kena strip naked.. Your car is 1.6 or the renault 1.8?why the timing belt so expensive?why allignment so expensive?15 can do it already what...

timing belt gates set 100000km- rm 140
fan belt mitsuboshi 5pk 1080 - rm 30
5pk 865 rm 18
proton waja rear d.pad (ceramic nao) rm 63
engine oil fully synthetic 5-40 toyota - rm 125
proton ori oil filter - rm 8
REVO advanced engine friction reducer & modifier 30ml ( NO NEED USE- JUST FOR THE ENGINE TAT MAKAN MINYAK HITAM USE ONLY)
Rear cam bolt - rm20 per pcs( not im selling- is any workshop oso sell this price)

This post has been edited by kelvin3900: Mar 1 2010, 01:07 AM

Hey guys..actually I got ask this before,bout my head light.

Here the picture.
Is it normal during raining it will look like that?? my car is new just a few months but actually I think its not normal.
After my second service got ask SC but they said normal..very blurr

Both side also like this? For me, my headlamp also got blur sometimes in a cold morning & will back to normal for after a while...

masuk moisture. if under warranty ask for change.

most of the time wut they will do is put sealant around the headlamp there... then use blow dryer to cure it....

Hmm..if like that I will try ask other SC.
Hope they will do something.Nice headlamp but look cheap if see like that ~~lol

hey.. my driver side wiper mounting to the car body broken d... its all cacat now. anyone know where can fix n how much?

Just change front Sachs absorber, absorber mounting & absorber bush yesterday cos spoil..

Sachs absorber x2 = RM360
Absorber bush x2 = RM70
Absorber mounting x2 = RM240
Camber adjustment = RM40

Total = RM710

Now pokai jor...

hello fellow waja owners, i'm currently driving a 1.6 Auto 4g18 waja.

i've learned from another thread that to improve torque slightly, a s-flow muffler would be a good choice but some say the straight flow would be better.

can anyone provide an insight on how these 2 types differ? and which would be better for torque?

The S-Flow is best for auto configuration as it's maintain the back-pressure of the exhaust system.

thanks, does it improve torque in any way? or just for show purposes?

Andy bought & use the DIY VS ar? How the result ..

i bought zaptor one last time.. cabut d.. useless... drain my battery got la

guys if i were to change my filter to K&N air filter, drop-in or open pod is better? the differences?

Lolz... I using Pivot MegaRaizin Purple colour 1... its effective for me.. no draining battery..

Just use drop in more than enuff... I using Super S stainless steel filter.. I feel can gain pick up..

For sure..the torque will improve much better.

---

Added on March 1, 2010, 4:01 pmMine using drop-in. If you don't modified much the engine better stick to drop-in, cause open-pod most of the time doesn't guide air intake properly, thus making the power loss.

This post has been edited by b48753: Mar 1 2010, 04:01 PM