kk ..lol lets find a meetup point .. which direction u okie ?

---

Added on February 5, 2010, 2:11 pmya at least ur ride is back to its handsome state haha .. insurance have to wait ..

This post has been edited by xin: Feb 5 2010, 02:11 PM

btw, anyone knows why would the new paint job be rough to the touch?

Here is the spot from Leisure Mall MAP Try to print out Got 1 KFC at the shop lot there.

This post has been edited by swk_sam: Feb 5 2010, 02:24 PM

guys,

my 2003 waja air-con switch speed 2 stop working. Speed 1,3,4 is working. Is there any way to repair it without changing the whole air-con selector panel ? and anyone know where I can buy it cheap

thanks,

I think u need to check which part goes wrong before come in to conclusion.. maybe control panel, maybe some parts

---

Added on February 6, 2010, 9:15 amxin, my time may change to 3+ cos need to do something 1st..
This thread keep on sinking again...

This post has been edited by swk_sam: Feb 6 2010, 10:17 AM

anyone here know how to dismantle front headlamps?

http://forum.lowyat.net/index.php?showtopi...&#entry25959630
can refer here.. if anything can ask me oso.. but i'm not that pro.. thats my 1st time doing oso.. hehe..

oh. nola i dont wanna blacken it. i just wanna remove the whole lamp so that i can adjust the height of the beam using a screw. lol. but your headlamps look good whats the heat gun for btw?

Wana ask our waja ecu can be reflash or not?

Heat gun is used for heating up the seal around the headlamp and the rear plastic which used to prevent water from entering the headlamp.

Heard our ecu can't be reflash and it's a self learning one.


Hey , any Ipohnians here coming back to Ipoh soon and any possibility helping me buy the hks grounding kit from Ken ?

This post has been edited by Andy0625: Feb 7 2010, 02:33 AM

Anybody hav AUX cable fix at the original HU?
For Waja CPS HU, do they already have the cable or i need to add on

Bro I found the HID at Brothers are much cheaper..if u look at it you're damn pissed off..but just wonder on the quality.

I going back Ipoh on Saturday.. U can contact Ken & ask him to pass me your cable if u want.
RM160 also got... If u trust the quality, u can go ahead ba.. But brother's price not include installation.. some if got problem they will delay u... If u grab & go at brother's then is ok...

This post has been edited by swk_sam: Feb 7 2010, 12:12 PM

huh.. no need take out the lamp oso can.. but if u insist then there is 4 bolt u need to take out.. 1 is at the inner side of the fender, 2 is on top of the lamp.. another one is behind the front grill.. u need to take out the grill 1st in order to do so.. after that just unplug the wiring behind the headlamp and pull out the lamp.. the left side lamp is usually abit hard to take out since the wiper's water tank is there.. if can't u can try to open the round part of the lamp housing at at the back.. twist it to open.. i don't remember clockwise or anticlockwise..

Anyone had a good job for full car soundproofing??

Also any of u guys installed cruise control on ur rides?

swk_sam, u selling HID isit? Can u PM me the details if you are?

http://img.mudah.my/images/44/4445219366.jpg
to anyone who like the neo R3 design bumper.. now is also available in waja mode.. hahaha

would like to know too if anyone did an effective sound proofing for doors??as the power windows tend to spoil "quite easily"......
if do soundproof and power window fail nid to take out all the soundproofing material??hw about sound proofing for fenders wad its for???

Wah.. Like that also can..

ever since neo R3 were introduce.. the bumper is likely to be used to other car.. 1st i see used on old satria also applicable to wira.. next on the list is persona/gen2.. and finally waja.. hahaha.. it would be nicer if the mouth is abit small..

i still prefer the R3 design, lovin it


This post has been edited by jolipoli81: Feb 8 2010, 02:48 AM