sifus... thanks for the guide so far..

aida64 @ everest is stating 45+- on the cpu sensor. and the room temp is quite hot. the pc is in a non a/c room.

is it a normal temp for those who unlock to 4 cores? or it should be lower??

All Phenom, I doubled my Sempron's core, can post?

idle temp not too important. give them OCCT and see how much full load temp. better make sure them below 65~70c.
if want to check cooler working fine or not, disable 2 core as normal n test its full load. your cooler high end air cooler already can compare to basic wc such as h50/60

Your temp is definitely high for a cooler like d14. Take mine for example.
I'm using Venomous-X + scythe gt in non-a/c room oc to 3.8 @ 1.44v. Idle @ 36C (CPU temp), gaming @ 45C and load prime95 @ 53C.
Mine also an unlock version of phenom ii 550.

Your should be much lower considering only minor oc @ 1.344v. How about your casing airflow???

This post has been edited by haziqk10: Sep 24 2011, 10:18 PM

ya.. i was shocked wen i saw the temp. i think i'll definitely reapply and reseat the cooler.
btw, i just finished an hour of OCCT test, no error found and the highest temp i got is only 59C. i'm currently opening all the side panels and top panels of the case.

wow.. urs looks very rock solid.. whats the highest/ maximum safe point vcore a normal phenom proc can achieve? 1.44v wont be too high??

Amd recommend up until 1.425v and for me I personally would limit up to 1.45v.
It is the temp that we should be concerned for. I prefer my temp to be lower than 55c during load.

Mine oc moderate only. Many sifu here oc their proc pass 4ghz mark.

guy u know how higher temp can make OCCT test fail? its fail on random core after i close side panel casing. about 2~3min test it occur. if open it side back no problem in OCCT, even 10h

What is your temp during load?? Amd suggest below 62C.

open case:


close case TMPIN1 ~70c. random error OCCT #core

Which one is the cpu temp??...you hv serious problem bro...90C!!!

no idea..maybe temp reading not accurate. seem tmpin1 same as read in et6 and everest and speedfan. but if disable unlocked core temp read ech core about 7~10c lower than tmpin1

If that is the cpu temp then you are way over the safe temp.
Even for the close case I think your temp are just 2C from AMD suggested temp.
Maybe you can try reseat your d14 or make sure that your case have a positive airflow.

no bro i use hdt s1283, no prob with its seat. i oc also htlink n nb, maybe they overheat n make core fail test?

sorry mistaken you with the other guy
How about share your cpu-z for the cpu and memory tab...also share you voltage here...

here u go:

nb voltage is 1.4v

new mobo inb4 old mobo ga ma74gmt s2 fail in unlock

Lower the HT link to 2000mhz. The voltage that you need to increase is cpu-nb, not the nb.
Your voltage is quite high. Lower the voltage a little.

oh mai its actually cpu-nb voltage, not nb.
if lower volt cant ler stable @3.5ghz..sure got bsod...htlink seem stable at 2400..this is 10h test:


but cannot close the casing

the first time i tried to unlock 4th core few months back, i manage to do it. but then system a little bit unstable thus i disable it back. last night i wanted to try again, and it's doesnt work anymore. it doesnt load anything until i have to remove the battery.

how is the success rate for unlocking lately?
keep see failure...

i think it sympton from bad core locked. what your mobo power phase again