need tweak some setting in RAM

post ur SS with Memset too~

tonight will post bro

I'm using Xigmatek HDT-SD964 and at idle it's around 3x degrees.. At full load i'm not really sure haven't really checked it yet..
Oh yer my SD964 is in 2 fan push pull configuration..
Don't have any screenshot of the temp though..

for ya reference bro, it was done w/ 10th anni:

http://forum.lowyat.net/index.php?act=Atta...=post&id=486787

nice rig there mate... 9850 b.e idle @ 3x'C w/ stock clock?

This post has been edited by ah_khoo: Oct 17 2008, 11:32 AM

not good enuf i think.. mine around 52c at 1.48v (full load).. for quad core oc sure even hotter.. better get ccf

This post has been edited by sharkeer: Oct 17 2008, 11:26 AM

ya ya ma bro in town..
Oc oc oc...

ccf heatsink too big i thk.. cnt fit for CM elite series casing..
btw i thk price for xigmatec quite expensive ler.. cnt found cheap de...
Xigmatek HDT-SD964 js with 92mm fan ; CM hyper 212 with 120mm fan, i found that their price vy similiar.. js i thk elite series casing will not fit for CM hyper 212..

thats y im thking to get CM geminII S( RM119)..
xigmatek hdt-sd964 can get at this price or lower ar?

why not get s1283? it's just slightly behind true in performance but cost alot less than true. worth it if u ask me. d only let down is it can only blow up & not out.

i bought rm120 i think xigmatek 964 is better than geminII S.. for info check www.frostytech.com/

@ah_khoo

s1283 also quite big ler... this blow out or blow up with 120mm fan de i thk vy tough to fit in CM elite series de casing ar...if can fit mayb i can get CM hyper 212 (more buget, RM124)

@sharkeer

thx for the info..

d problem w/ cm mid tower casings is d width, that's one of d reason why i went for lian li recently. my praetorian which had served me well for d past 3 years (apart from not bein able to accommodate big @ss coolers) goin to be traded w/ a true...

This post has been edited by ah_khoo: Oct 17 2008, 11:48 AM

thats the prob with mid tower casing.. hsf now is really HUGE..

This post has been edited by sharkeer: Oct 17 2008, 11:59 AM

yalo.. more suitable to put blow in(blow toward proc) type cooler oni..
i prefer get a blow out(blow to bhind) type.. blive will hv beter air flow than blow in type..
so mayb js go to xigmatec sd964

that depends on your case cooling.. if u hv good air flow i think there is no prob..

This post has been edited by sharkeer: Oct 17 2008, 12:11 PM

The only drawback with xigmatek sd964 that i think is that the hsf can only be mounted vertically, which means the hot air would be blowing up towards the PSU..
I kinda like my old HyperTX2 which blows to the back which coincidentally just where my rear exhaust fan sits inside my oldie CM Praetorian case..
I'm itchy to try o/c my cpu but just can't yet since i haven't gotten my hands on any ramsinks to be paste on my mobo pwm's..

---

Added on October 17, 2008, 12:45 pmLucky u, i bought my SD964 at RM149.00

This post has been edited by cloudwan: Oct 17 2008, 12:45 PM

RM149? abit overprice

cant put horizontal meh? i put mine horizontally blows the air backwards.. here the ss

EDIT: Maybe position of the bracket on ur mobo different from mine.. if that so than u need to buy another mounting kit..

This post has been edited by sharkeer: Oct 17 2008, 01:02 PM


Attached thumbnail(s)

Ur mobo clip is on side ways so it point the HSF horizontally.. but my TA790GX has its clips at the top and below soooo the hsf would be directed vertically..
I even try it on my old K9A2-CF and same as my biostar it would be mounted vertically too..

EDIT: Yup i think its all about the bracket too.. Have to check 1st the bracket on ur mobo before any decision, i didn't know..

This post has been edited by cloudwan: Oct 17 2008, 01:06 PM

huge is ok, but tall is no no...

blow down type can cool other components as well, give & take loh...

did u mod ya side panel mate? i blew 2 holes at d side (near hdd there, rite above sb area), makin my transparent window looked a bit cacat (but gud enuf to cool d nb which integrated w/ sb during nf4 era).

lucky u to have such bracket... xigmatek really ignore amd users coz most of their tower cooler are blow up (instead of blow out) type...

mean which type bracket will make it put as horizontal??
my mobo can or nt?



as the red frame is the way to put pin... will this can make it blow out(toward behind)?

-delete-

This post has been edited by cdlim87: Oct 17 2008, 01:42 PM