hint hint ppl..

the issue is.. he is using strap 400....

go look up on the maximus formula thread in xtremesystem..
that was the first board with strap 400...

its a long story for this one.

hi guys,

I also use E8400 C0, oc 4.005Ghz on 1.356v... so far almost 7hour ORTHOS test... but the temp is darn hot 73C load, idle at 49c... on CCF... dont know this temp is real or not..

Box cooler? If so its expected...

wow.
thats a lot of vdroop and damn hot for a CCF.

are u sure its attached properly??
are the fan spinning???

the fan is spinning fine... my airflow in casing a bit bad.. it can reach 66c if i use front fan but to loud

@zuhair
1000 cl5 @ 2.1vdim?
wow...dats high
would u like to share some of ur flex results?
i heard the older version can do miracle

[/quote]
this is flex pc9600 - the standard rating is 55518 @ 1200 - 2.10v (non micron). had it at 1290 55515 @ 2.1v stable

in bios, set @ 1.28175v. LLC enabled. idle @ 1.260v, load @ 1.272v


same as above

all setting are with LLC enabled

screenshot @ 535X8 @ 1.408v load + 1284 55515 PL8 @ 2.10v 20pass of LINPACK v1.80



screenshot @ 480X9 @ 1.416v load + 1280 55515 PL7 @ 2.10v 5hours of OCCT blend

watch the temp bro.............

[quote=zuhair,Nov 3 2008, 12:44 PM]
@zuhair
1000 cl5 @ 2.1vdim?
wow...dats high
would u like to share some of ur flex results?
i heard the older version can do miracle

[/quote]
this is flex pc9600 - the standard rating is 55518 @ 1200 - 2.10v (non micron). had it at 1290 55515 @ 2.1v stable
in bios, set @ 1.28175v. LLC enabled. idle @ 1.260v, load @ 1.272v
same as above

all setting are with LLC enabled

screenshot @ 535X8 @ 1.408v load + 1284 55515 PL8 @ 2.10v 20pass of LINPACK v1.80



screenshot @ 480X9 @ 1.416v load + 1280 55515 PL7 @ 2.10v 5hours of OCCT blend



[/quote]

Not bad not bad.
The sustainable PL is good for 535FSB
You run these setting daily??Run 1:1 as the performance gain is not much but lifespan of ram make difference,just what i think lah

now thats impressive

show some everest bandwidth dude... should be 11k++

This post has been edited by cstkl1: Nov 4 2008, 01:45 AM

nah, my 24/7 setting is at 4.0ghz and 1200 55515 PL8 @ 1.90v


will get to it after work.

everest bandwith

memory read


memory write


memory copy


memory latency


and bios setting for 1200mhz - this is for casperito

main setting - fsb


ram setting - alpha timing


ram setting - secondary


voltage




This post has been edited by zuhair: Nov 5 2008, 11:45 AM

hai bro,

just want to know what is normal vdrop? previously i set 1.21875v for 3825mhz stable in orthos for 7 hour.. just now my pc crash and restart suddenly.. i tried to run orthos and it fail just about 15sec (with 1.21875v bios vc).. dont now what happend..

i tried to set bios vcore to 1.256v then it stabilize.. but cpuz shows only 1.216v idle and 1.200v load in orthos

is this mean my vdrop = 0.04v, vdroop = 0.016v?

is this acceptable? my idle temp also increase from 39c to 43c.. why ah?

How bad is the vdroop depends on the motherboard, it varies. You increased the voltage so obviously the temp will increase a little.

clawhammer, what vcore you used to get E8200 4ghz stable on Foxconn Mars?

Sorry, I didn't notice the screenshot links were all broken I'm currently doing 515x8 (14-4-4-4) at 1.4875V and I'll try post a screenshot later today Previously I needed around 1.4125V to get it running 4Ghz stable (if I remember correctly).

Wah clawwy bro, that's a freakin high vcore there...btw, I'm running my E8400 C0 with 1.4v for 4ghz(500X8) right now...already passes 8 hours stressed test and everything but I still receive random BSOD when gaming n surfing the web...and my vNB is 1.4v...

I'm using the first few batches of E8200 so it doesn't overclock that superbly compared to the new E0's you guys are having Since it's an old junk then I might as well stress it more. If it's broken, I'll have a new excuse to get the E8600

I'm on water cooling and Small FFT at 1.4785V can go up to 64C-65C full load.

Mine is the first batch too...damn regret buying too early...

need help frm u all... can u guys comment smtg about my proc temp...

hmmm... something wrong with your proc's temp... mine oced at 3.6ghz on idle only 46C on core temp reading... but, your proc downclock also can reach 48C.... i wanna ask you.. why you downclock your proc?? and what cpu cooler you using now??

That is not downclock bro.
EIST & C1E in action.

-pWs-