u did clear d cmos didn't u???

it could be d bios set it to disable by default.

http://www.guru3d.com/article/amd-phenom-x...ocessor-tested/

sorry if double post..

tempting..

That's if you have 790GX.

If you don't, go grab both.

It you can wait, go grab Deneb.

Hey, i would like to ask, i've managed to push my CPU from 2.5ghx to 2.9ghz & it's stable but my prime95 test failed. It failed meaning it's not stable right? But it doesn't crashes so is it okay?








Attached thumbnail(s)

hello CelciuzX,
plz lower down ur HT frequency and try to prime again,
next, plz include ur memory tab.

yeah sometimes high HT makes it fail or restart when stress/ prime.. below 1000 is ok. doesnt make any significant difference right?


@bro xixo,
applying to which university? continue studying? wait.. how old are u?

fast SPI? i dunno what the significant.. coz never try to spot the different, later i try to spot it
i'm just sweet 17 really?

This post has been edited by xixo_12: Oct 4 2008, 05:04 PM

Here's my memory tab. If i get performance RAM, it can OC better right?


Attached thumbnail(s)

hello CelciuzX,
performance ram, u can oc higher /tight timing, it depend on urself, if u didnt satisfied, so up to u.

next,
change ur CR to 2T, and try prime again, leave ur vdimm at 2.0v or below, try urself

Whats CR to 2T? Noob here sorry. If i lower my vdimm from 2.1v to 2.0v or below, i'll get a BSOD & how do i lower my HT? My bios doesn't let me screw with that, when i increase my FSB it'll increase the HT too.

Owh, i understand whats CR to 2T. How do i change it? Cant find it in bios.

This post has been edited by CelciuzX: Oct 4 2008, 06:04 PM

Hello,
now try to change ur divider, use 533 divider, change CR to 2T

for CR 2T
-go to advanced tab->find timing mode->set to manual

for HT requency.
-go to advanced tab->find LDT bus Frequency and change to 800mhz

p/s: when u change divider, make sure the timing as memory tab, u follow, find the word that same like u saw at memory tab cpuz , in case of automatic change by bios according their factory setting

This post has been edited by xixo_12: Oct 4 2008, 06:24 PM

Bro, i changed my ram to 800mhz & my LDT to 800mhz. My comp failed to boot, not even a beep sound during start up.

I cleared my cmos & it still was the same, luckily when i took out everything & put i back in, it could boot as usual. Kinda freaked me out.

Mind telling me what did i do wrong?

hello,
mind to elaborates more?


my previous post

This post has been edited by xixo_12: Oct 5 2008, 01:03 AM

Well, after i change my Timing from Auto to Manual, i changed the memory clock frequency to 800mhz.

I still cant find that option in my bios bro. Under Chipset, it only allow me to change my ram memory clock frequency.

hello
go to advanced->chipset->dram configuration->timing mode(manual)->memory clock frequency(DDR2 533)
what i bold is the value that u need to change

when u change to DDR2 800, it lead u to failure as u over the limit of the ram as ur HTT increase

This post has been edited by xixo_12: Oct 5 2008, 01:37 AM

My default speed is 667mhz right? So i need to change to 533mhz & change my LDT/PCI frequency to 800mhz?

Just wanna clarify cause that incident really gave me a heart attack just now. haha

yes
others setting same like ur overclocked system
from what i observed, i didnt see any timing setting on ur board, so i really can't help u on that part. maybe through bios update or i really missed out that area, then it really sorry

This post has been edited by xixo_12: Oct 5 2008, 01:52 AM

OCed my proc edy.. will collect info on OC my ram after this.. mind to tell where to start 1st?

Dude, i changed my LDT to 800mhz & it couldn't boot like the previous time. Need to take out my cpu to reset it.

does increase vdimm help?